AT25640AN-10SI-2.7 SL383 Atmel, AT25640AN-10SI-2.7 SL383 Datasheet - Page 7
![IC EEPROM 64KBIT 20MHZ 8SOIC](/photos/6/50/65032/453-8-soic_sml.jpg)
AT25640AN-10SI-2.7 SL383
Manufacturer Part Number
AT25640AN-10SI-2.7 SL383
Description
IC EEPROM 64KBIT 20MHZ 8SOIC
Manufacturer
Atmel
Datasheet
1.AT25080A-10PU-2.7.pdf
(26 pages)
Specifications of AT25640AN-10SI-2.7 SL383
Format - Memory
EEPROMs - Serial
Memory Type
EEPROM
Memory Size
64K (8K x 8)
Speed
10MHz, 20MHz
Interface
SPI, 3-Wire Serial
Voltage - Supply
2.7 V ~ 5.5 V
Operating Temperature
-40°C ~ 85°C
Package / Case
8-SOIC (3.9mm Width)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Other names
AT25640AN10SI27SL
2. Serial Interface Description
3347L–SEEPR–06/07
MASTER: The device that generates the serial clock.
SLAVE: Because the Serial Clock pin (SCK) is always an input, the AT25080A/160A/320A/640A
always operates as a slave.
TRANSMITTER/RECEIVER: The AT25080A/160A/320A/640A has separate pins designated
for data transmission (SO) and reception (SI).
MSB: The Most Significant Bit (MSB) is the first bit transmitted and received.
SERIAL OP-CODE: After the device is selected with CS going low, the first byte will be
received. This byte contains the op-code that defines the operations to be performed.
INVALID OP-CODE: If an invalid op-code is received, no data will be shifted into the
AT25080A/160A/320A/640A, and the serial output pin (SO) will remain in a high impedance
state until the falling edge of CS is detected again. This will reinitialize the serial communication.
CHIP SELECT: The AT25080A/160A/320A/640A is selected when the CS pin is low. When the
device is not selected, data will not be accepted via the SI pin, and the serial output pin (SO) will
remain in a high impedance state.
H O L D : T h e H O L D p i n i s u s e d i n c o n j u n c t i o n w i t h t h e C S p i n t o s e l e c t t h e
AT25080A/160A/320A/640A. When the device is selected and a serial sequence is underway,
HOLD can be used to pause the serial communication with the master device without resetting
the serial sequence. To pause, the HOLD pin must be brought low while the SCK pin is low. To
resume serial communication, the HOLD pin is brought high while the SCK pin is low (SCK may
still toggle during HOLD). Inputs to the SI pin will be ignored while the SO pin is in the high
impedance state.
WRITE PROTECT: The write protect pin (WP) will allow normal read/write operations when held
high. When the WP pin is brought low and WPEN bit is “1”, all write operations to the status reg-
ister are inhibited. WP going low while CS is still low will interrupt a write to the status register. If
the internal write cycle has already been initiated, WP going low will have no effect on any write
operation to the status register. The WP pin function is blocked when the WPEN bit in the status
register is “0”. This will allow the user to install the AT25080A/160A/320A/640A in a system with
the WP pin tied to ground and still be able to write to the status register. All WP pin functions are
enabled when the WPEN bit is set to “1”.
AT25080A/160A/320A/640A
7