AT49BV163D-70TU Atmel, AT49BV163D-70TU Datasheet
AT49BV163D-70TU
Specifications of AT49BV163D-70TU
Available stocks
Related parts for AT49BV163D-70TU
AT49BV163D-70TU Summary of contents
Page 1
... Green (Pb/Halide-free) Packaging 1. Description The AT49BV163D( 2.7-volt 16-megabit Flash memory organized as 1,048,576 words of 16 bits each or 2,097,152 bytes of 8 bits each. The x16 data appears on I/O0 - I/O15; the x8 data appears on I/O0 - I/O7. The memory is divided into 39 sectors for erase operations. The device is offered in a 48-lead TSOP and a 48-ball CBGA pack- age ...
Page 2
... TSOP (Type 1) Top View A15 1 A14 2 A13 3 A12 4 A11 5 A10 A19 RESET RDY/BUSY 15 A18 16 A17 AT49BV163D(T) 2 2.2 48-ball CBGA Top View (Ball Down) 48 A16 47 BYTE 46 GND 45 I/O15/A-1 44 I/O7 43 I/O14 42 I/O6 41 I/O13 40 I/O5 39 I/O12 38 I/O4 37 VCC 36 I/O11 35 I/O3 34 I/O10 33 I/O2 32 I/O9 31 I/O1 30 I/ GND 26 ...
Page 3
... Read The AT49BV163D(T) is accessed like an EPROM. When CE and OE are low and WE is high, the data stored at the memory location determined by the address pins are asserted on the out-puts. The outputs are put in the high impedance state whenever high. This dual- line control gives designers flexibility in preventing bus contention ...
Page 4
... I/O5, I/O6 and I/O7. The the function of these bits. To provide greater flexibility for system designers, the AT49BV163D(T) contains a programmable configuration register. The configuration register allows the user to specify the status bit operation. The configuration register can be set to one of two different values, “00” or “01”. If the configuration register is set to “00”, the part will automati- cally return to the read mode after a successful program or erase operation. If the configuration register is set to a “ ...
Page 5
... DATA Polling The AT49BV163D(T) features Data Polling to indicate the end of a program cycle. If the status configuration register is set to a “00”, during a program cycle an attempted read of the last byte/word loaded will result in the complement of the loaded data on I/O7. Once the program cycle has been completed, true data is valid on all outputs and the next cycle may begin. During a chip or sector erase operation, an attempt to read the device will give a “ ...
Page 6
... Product Identification The product identification mode identifies the device and manufacturer as Atmel accessed using a software operation. For details, see sections on AT49BV163D(T) 6 page 21), a read from address location 00002H within a sector will show “Operating Modes” on page 15 page 21. ...
Page 7
... Protection Register The AT49BV163D(T) contains a 128-bit register that can be used for security purposes in sys- tem design. The protection register is divided into two 64-bit blocks. The two blocks are designated as block A and block B. The data in block A is non-changeable and is programmed at the factory with a unique number ...
Page 8
... During chip erase, a valid address is any non-protected sector address. 2. I/O7 should be rechecked even if I/O5 = “1” because I/O7 may change simultaneously with I/O5. AT49BV163D(T) 8 Figure 4-2. YES YES Program/Erase ...
Page 9
... I/O5 = “1” because the toggle bit may stop toggling as I/O5 changes to “1”. 3590A–FLASH–12/05 Figure 4- Program/Erase Operation Successful, Device in Read Mode Note: AT49BV163D(T) Toggle Bit Algorithm (Configuration Register = 01) START Read I/O7 - I/O0 Read I/O7 - I/O0 NO Toggle Bit = Toggle YES NO I/ ...
Page 10
... Program Suspended & Read Programming Sector Program Suspended & Read Non-programming Sector Notes: 1. I/O5 switches to a “1” when a program or an erase operation has exceeded the maximum time limits or when a program or sector erase operation is performed on a protected sector. AT49BV163D(T) 10 I/O7 I/O7 I/ ...
Page 11
... AA AAA 55 555 F0 ( AAA 55 555 C0 AA AAA 55 555 C0 AA AAA 55 555 90 AA AAA 55 555 D0 98 AT49BV163D(T) 4th Bus 5th Bus Cycle Cycle Addr Data Addr Data 555 AA AAA 55 555 AA AAA 55 Addr D IN 555 AA AAA 55 555 AA AAA 55 (7) Addr D IN 080 ...
Page 12
... The addressing shown above should be used when the device is operating in the word (x16) mode the byte (x8) mode, A-1 should be used when addressing the protection register: with A the LSB of the address location can be accessed; and with A the MSB of the address location can be accessed AT49BV163D(T) 12 *NOTICE: + 0.6V ...
Page 13
... AT49BV163D – Sector Address Table Sector Size (Bytes/Words) SA0 8K/4K SA1 8K/4K SA2 8K/4K SA3 8K/4K SA4 8K/4K SA5 8K/4K SA6 8K/4K SA7 8K/4K SA8 64K/32K SA9 64K/32K SA10 64K/32K SA11 64K/32K SA12 64K/32K SA13 64K/32K SA14 64K/32K SA15 64K/32K SA16 ...
Page 14
... AT49BV163DT – Sector Address Table Sector Size (Bytes/Words) SA0 64K/32K SA1 64K/32K SA2 64K/32K SA3 64K/32K SA4 64K/32K SA5 64K/32K SA6 64K/32K SA7 64K/32K SA8 64K/32K SA9 64K/32K SA10 64K/32K SA11 64K/32K SA12 64K/32K SA13 64K/32K SA14 64K/32K SA15 64K/32K SA16 ...
Page 15
... Refer to AC programming waveforms on 3. Manufacturer Code: 1FH (x8); 001FH (x16), Device Code: C0H (x8)-AT49BV163D; 01C0H (x16)-AT49BV163D; C2H (x8)-AT49BV163DT; 01C2H (x16)-AT49BV163DT. 4. Additional device code: 01H (x8) – AT49BV163D(T); 001H (x16) – AT49BV163D(T). 5. See details under “Software Product Identification Entry/Exit” on 13. DC Characteristics ...
Page 16
... Input Test Waveforms and Measurement Level 15. Output Test Load 16. Pin Capacitance ( MHz 25°C Symbol Typ OUT Note: 1. This parameter is characterized and is not 100% tested. AT49BV163D(T) 16 2.0V 0. < Max Units Conditions OUT 3590A–FLASH–12/05 ...
Page 17
... This parameter is characterized and is not 100% tested. 3590A–FLASH–12/05 (1)(2)(3)( ADDRESS VALID ACC t RO HIGH after the address transition without impact on t ACC after the falling edge of CE without impact AT49BV163D(T) AT49BV163D(T)-70 Min Max 100 OUTPUT VALID . ACC after an address change CE ...
Page 18
... Chip Select Setup Time CS t Chip Select Hold Time CH t Write Pulse Width ( Write Pulse Width High WPH t Data Setup Time Data, OE Hold Time DH OEH 20. AC Byte/Word Load Waveforms 20.1 WE Controlled 20.2 CE Controlled AT49BV163D(T) 18 Min Max Units 3590A–FLASH–12/05 ...
Page 19
... WPH 555 AAA 555 ADDRESS DATA ( WPH 555 AAA 555 555 WORD 0 WORD 1 WORD 2 WORD 3 11.) AT49BV163D(T) Min Typ Max 500 16 0.1 0.5 500 t BP 555 INPUT AA DATA AAA Note SEC1/2 55 Note 3 WORD 4 WORD 5 Units 120 µ seconds 2.0 seconds 6.0 ...
Page 20
... Read Characteristics” on page OE 27. Toggle Bit Waveforms Notes: 1. Toggling either both OE and CE will operate toggle bit. The t input(s). 2. Beginning and ending state of I/O6 will vary. 3. Any address location may be used but the address should not vary. AT49BV163D(T) 20 (1) 17. t OEH t DH ...
Page 21
... The device returns to standard operation mode. 5. Manufacturer Code: 1FH(x8); 001FH(x16) Device Code:C0H (x8) - AT49BV163D; 01C0H (x16) - AT49BV163D; C2H (x8) - AT49BV163DT; 01C2H (x16) - AT49BV163DT. Additional Device Code: 01H(x8) – AT49BV163D(T); 0001H(x16) – AT49BV163D(T) 6. Either one of the Product ID Exit commands can be used. 3590A–FLASH–12/05 30. Sector Lockdown Enable Algorithm ...
Page 22
... AT49BV163D(T) 22 Data Comments 0051h “Q” 0052h “R” 0059h “Y” 0002h 0000h 0041h 0000h 0000h 0000h 0000h 0000h 0027h V ...
Page 23
... Bit 1 – 8-word page, 0 – no, 1 – yes Undefined bits are “0” 0080h Location of protection register lock byte, the section’s first byte 0003h # of bytes in the factory prog section of prot register – 2*n 0003h # of bytes in the user prog section of prot register – 2*n AT49BV163D(T) 23 ...
Page 24
... Standby 70 15 0.025 48C19 48-ball, Plastic Chip-Size Ball Grid Array Package (CBGA) 48T 48-lead, Plastic Thin Small Outline Package (TSOP) AT49BV163D(T) 24 Ordering Code Package AT49BV163D-70CU 48C19 AT49BV163DT-70CU AT49BV163D-70TU AT49BV163DT-70TU Package Type Operation Range Industrial (-40° to 85°C) 48T 3590A–FLASH–12/05 ...
Page 25
... Ball Corner e 1.20 REF Ø Bottom View TITLE 48C19, 48-ball ( Array), 0.80 mm Pitch, 6.0 x 8.0 x 1.0 mm Chip-scale Ball Grid Array Package (CBGA) AT49BV163D( Side View COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX E 5.90 6.00 6.10 E1 4.0 TYP D 7.90 8.00 8 ...
Page 26
... E Notes: 1. This package conforms to JEDEC reference MO-142, Variation DD. 2. Dimensions D1 and E do not include mold protrusion. Allowable protrusion 0.15 mm per side and 0.25 mm per side. 3. Lead coplanarity is 0.10 mm maximum. 2325 Orchard Parkway San Jose, CA 95131 R AT49BV163D(T) 26 PIN SEATING PLANE A1 TITLE ...
Page 27
... Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT ...