AT27BV512-70RU Atmel, AT27BV512-70RU Datasheet
AT27BV512-70RU
Specifications of AT27BV512-70RU
Available stocks
Related parts for AT27BV512-70RU
AT27BV512-70RU Summary of contents
Page 1
... AT27BV512 consumes less than one fifth the power standard 5V EPROM. Standby mode supply current is typically less than 1 µA at 3V. The AT27BV512 simpli- fies system design and stretches battery lifetime even further by eliminating the need for power supply regulation. The AT27BV512 is available in industry-standard JEDEC-approved one-time programmable (OTP) plastic PLCC, SOIC, and TSOP packages ...
Page 2
... Product Identification Code electronically identifies the device and manufacturer. This feature is used by industry-standard programming equipment to select the proper programming algo- rithms and voltages. The AT27BV512 programs exactly the same way as a standard 5V AT27C512R and uses the same programming equipment. 2. Pin Configurations ...
Page 3
... Maximum Ratings” may cause permanent dam- age to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the (1) operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect (1) device reliability (1) AT27BV512 3 ...
Page 4
... Operating Temperature (Case) V Power Supply CC AT27BV512 A15 = V ≤ 3.6V, or 4.5V ≤ except A9 which is set ( ( Identification Code ≤ 5.5V 6.5V. CC and A0 which is toggled select the Device Code byte. IH AT27BV512-70 -40°C - 85°C 2.7V to 3.6V 5V ± 10% Outputs D OUT High Z High OUT High Z 0602E–EPROM–12/07 ...
Page 5
... I (CMOS SB1 CC I (TTL 2 0.5V SB2 MHz mA OUT 2 -400 µ and removed simultaneously with or after OE except during programming. The supply current would then be the sum AT27BV512 Min Max ±1 ± 100 = 3.6V 8 -0.6 0.8 -0 0 0.4 ...
Page 6
... When reading a AT27BV256, a 0.1 µF capacitor is required across V AT27BV512 6 Condition after the falling edge of CE without impact after the address is valid without impact on t ACC OE CC AT27BV512-70 Min Max ACC and ground to suppress spurious voltage transients. 0602E–EPROM–12/07 Units ...
Page 7
... Output Test Load 13. Pin Capacitance ( MHz 25°C Symbol Typ OUT Note: 1. Typical values for nominal supply voltage. This parameter is only sampled and is not 100% tested. 0602E–EPROM–12/ < (10 Note 100 pF including jig capacitance. Max 6 12 AT27BV512 Units Conditions OUT 7 ...
Page 8
... Programming Waveforms Notes: 1. The Input Timing Reference is 0.8V for and t are characteristics of the device but must be accommodated by the programmer. OE DFP 3. When programming the AT27BV512, a 0.1 µF capacitor is required across V transients. AT27BV512 8 (1) and 2.0V for and ground to suppress spurious voltage PP 0602E–EPROM–12/07 ...
Page 9
... Program Pulse width tolerance is 100 µsec ± 5%. 17. Atmel’s AT27BV512 Integrated Product Identification Code Codes A0 Manufacturer 0 Device Type 1 Note: 1. The AT27BV512 has the same Product Identification Code as the AT27C512R. Both are programming compatible. 0602E–EPROM–12/07 = 13.0 ± 0.25V PP Test Conditions ...
Page 10
... After the byte verifies properly, the next address is selected until all have been checked. OE/V are read again and compared with the original data to determine if the device passes or fails. AT27BV512 10 is raised to 13.0V. Each address is first programmed with one ...
Page 11
... Wide, Plastic Gull Wing Small Package (SOIC) 28T 28-lead, Plastic Thin Small Outline Package (TSOP) 0602E–EPROM–12/07 Ordering Code AT27BV512-70JI AT27BV512-70RI AT27BV512-70TI Ordering Code AT27BV512-70JU AT27BV512-70RU AT27BV512-70TU Package Type AT27BV512 Package Operation Range 32J Industrial (1) 28R (-40°C to 85°C) ...
Page 12
... Allowable protrusion is .010"(0.254 mm) per side. Dimension D1 and E1 include mold mismatch and are measured at the extreme material condition at the upper or lower parting line. 3. Lead coplanarity is 0.004" (0.102 mm) maximum. 2325 Orchard Parkway San Jose, CA 95131 R AT27BV512 12 1.14(0.045) X 45˚ PIN NO. 1 IDENTIFIER E1 E ...
Page 13
... Mold Flash or protrusion shall not exceed 0.25 mm (0.010"). 2325 Orchard Parkway San Jose, CA 95131 R 0602E–EPROM–12/ TITLE 28R, 28-lead, 0.330" Body Width, Plastic Gull Wing Small Outline (SOIC) AT27BV512 COMMON DIMENSIONS (Unit of Measure = mm) MIN MAX SYMBOL NOM A 2.39 – 2.79 A1 0.050 – 0.356 D 18 ...
Page 14
... E Notes: 1. This package conforms to JEDEC reference MO-183. 2. Dimensions D1 and E do not include mold protrusion. Allowable protrusion 0.15 mm per side and 0.25 mm per side. 3. Lead coplanarity is 0.10 mm maximum. 2325 Orchard Parkway San Jose, CA 95131 R AT27BV512 14 PIN SEATING PLANE A1 TITLE 28T, 28-lead (8 x 13.4 mm) Plastic Thin Small Outline Package, Type I (TSOP) 0º ...
Page 15
... Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT ...