M24C32-WMN6T STMicroelectronics, M24C32-WMN6T Datasheet - Page 14
![IC EEPROM 32KBIT 400KHZ 8SOIC](/photos/1/38/13851/497-8-soic_sml.jpg)
M24C32-WMN6T
Manufacturer Part Number
M24C32-WMN6T
Description
IC EEPROM 32KBIT 400KHZ 8SOIC
Manufacturer
STMicroelectronics
Datasheet
1.M24C32-RDW6TP.pdf
(42 pages)
Specifications of M24C32-WMN6T
Format - Memory
EEPROMs - Serial
Memory Type
EEPROM
Memory Size
32K (4K x 8)
Speed
400kHz
Interface
I²C, 2-Wire Serial
Voltage - Supply
2.5 V ~ 5.5 V
Operating Temperature
-40°C ~ 85°C
Package / Case
8-SOIC (3.9mm Width)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Other names
497-1618-2
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
M24C32-WMN6T
Manufacturer:
STM
Quantity:
2 736
Part Number:
M24C32-WMN6T
Manufacturer:
ST
Quantity:
20 000
Company:
Part Number:
M24C32-WMN6TP
Manufacturer:
NUMONYX
Quantity:
5 000
Part Number:
M24C32-WMN6TP
Manufacturer:
ST
Quantity:
20 000
Company:
Part Number:
M24C32-WMN6TP/C
Manufacturer:
ST
Quantity:
1 275
Company:
Part Number:
M24C32-WMN6TR
Manufacturer:
SANYO
Quantity:
7
Device operation
4.5
14/42
Memory addressing
To start communication between the bus master and the slave device, the bus master must
initiate a Start condition. Following this, the bus master sends the device select code, shown
in
Table 4.
1. The most significant bit, b7, is sent first.
2. E0, E1 and E2 are compared against the respective external pins on the memory device.
The device select code consists of a 4-bit device type identifier, and a 3-bit Chip Enable
“Address” (E2, E1, E0). The 4-bit device type identifier 1010b addresses the memory array
(M24C32 and M24C32-D), and the 4-bit device type identifier 1011b addresses the
Identification page (M24C32-D only). A device select code handling a value other than
1010b or 1011b is not acknowledged by the device.
Up to eight memory devices can be connected on a single I
unique 3-bit code on the Chip Enable (E0, E1, E2) inputs. When the device select code is
received, the device only responds if the Chip Enable Address is the same as the value on
the Chip Enable (E0, E1, E2) inputs.
The 8
If a match occurs on the device select code, the corresponding device gives an
acknowledgment on Serial Data (SDA) during the 9
the device select code, it deselects itself from the bus, and goes into Standby mode.
Table 5.
1. X =
Device select code
when addressing the
memory array
Device select code
when accessing the
Identification page
Current Address
Read
Random Address
Read
Sequential Read
Byte Write
Page Write
Table 2
th
Mode
V
IH
bit is the Read/Write bit (RW). This bit is set to 1 for Read and 0 for Write operations.
or V
(on Serial Data (SDA), most significant bit first).
IL
Device select code
Operating modes
.
RW bit WC
1
0
1
1
0
0
b7
1
1
V
V
X
X
X
X
Device type identifier
IL
IL
(1)
Doc ID 4578 Rev 18
b6
0
0
Bytes
≤ 32
≥ 1
1
1
1
M24C32-DF, M24C32-W, M24C32-R, M24C32-F
b5
1
1
(1)
th
Start, device select, RW = 1
Start, device select, RW = 0, Address
reStart, device select, RW = 1
Similar to Current or Random Address
Read
Start, device select, RW = 0
Start, device select, RW = 0
b4
0
1
bit time. If the device does not match
Chip Enable address
2
b3
E2
E2
C bus. Each one is given a
Initial sequence
E1
E1
b2
b1
E0
E0
(2)
RW
RW
RW
b0