M29W320DB90N6 NUMONYX, M29W320DB90N6 Datasheet - Page 38
![no-image](/images/manufacturer_photos/0/4/484/numonyx_sml.jpg)
M29W320DB90N6
Manufacturer Part Number
M29W320DB90N6
Description
IC FLASH 32MBIT 90NS 48TSOP
Manufacturer
NUMONYX
Series
Axcell™r
Datasheet
1.M29W320DB70N6.pdf
(44 pages)
Specifications of M29W320DB90N6
Format - Memory
FLASH
Memory Type
FLASH - Nor
Memory Size
32M (4Mx8, 2Mx16)
Speed
90ns
Interface
Parallel
Voltage - Supply
2.7 V ~ 3.6 V
Operating Temperature
-40°C ~ 85°C
Package / Case
48-TSOP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
M29W320DB90N6(LEAD)
Manufacturer:
ST
Quantity:
556
Company:
Part Number:
M29W320DB90N6F
Manufacturer:
ST
Quantity:
1 000
M29W320DT, M29W320DB
APPENDIX C. BLOCK PROTECTION
Block protection can be used to prevent any oper-
ation from modifying the data stored in the Flash.
Each Block can be protected individually. Once
protected, Program and Erase operations on the
block fail to change the data.
There are three techniques that can be used to
control Block Protection, these are the Program-
mer technique, the In-System technique and Tem-
porary Unprotection. Temporary Unprotection is
controlled by the Reset/Block Temporary Unpro-
tection pin, RP; this is described in the Signal De-
scriptions section.
Unlike the Command Interface of the Program/
Erase Controller, the techniques for protecting and
unprotecting blocks change between different
Flash memory suppliers. For example, the tech-
niques for AMD parts will not work on STMicro-
electronics parts. Care should be taken when
changing drivers for one part to work on another.
Programmer Technique
The Programmer technique uses high (V
age levels on some of the bus pins. These cannot
be achieved using a standard microprocessor bus,
therefore the technique is recommended only for
use in Programming Equipment.
To protect a block follow the flowchart in Figure 18,
Programmer Equipment Block Protect Flowchart.
To unprotect the whole chip it is necessary to pro-
tect all of the blocks first, then all blocks can be un-
protected at the same time. To unprotect the chip
follow Figure 19, Programmer Equipment Chip
Unprotect Flowchart. Table 27, Programmer
Table 27. Programmer Technique Bus Operations, BYTE = V
38/44
Block Protect
Chip Unprotect
Block Protection
Verify
Block Unprotection
Verify
Operation
V
V
V
V
E
ID
IL
IL
IL
V
V
V
V
G
ID
ID
IL
IL
V
V
IL
IL
V
V
W
Pulse
Pulse
IH
IH
ID
A0 = V
A0 = V
) volt-
A9 = V
A9 = V
IL
IL
A12-A20 Block Address
A12-A20 Block Address
, A1 = V
, A1 = V
ID
ID
, A12-A20 Block Address
Address Inputs
, A12 = V
Technique Bus Operations, gives a summary of
each operation.
The timing on these flowcharts is critical. Care
should be taken to ensure that, where a pause is
specified, it is followed as closely as possible. Do
not abort the procedure before reaching the end.
Chip Unprotect can take several seconds and a
user message should be provided to show that the
operation is progressing.
In-System Technique
The In-System technique requires a high voltage
level on the Reset/Blocks Temporary Unprotect
pin, RP. This can be achieved without violating the
maximum ratings of the components on the micro-
processor bus, therefore this technique is suitable
for use after the Flash has been fitted to the sys-
tem.
To protect a block follow the flowchart in Figure 20,
In-System Block Protect Flowchart. To unprotect
the whole chip it is necessary to protect all of the
blocks first, then all the blocks can be unprotected
at the same time. To unprotect the chip follow Fig-
ure 21, In-System Chip Unprotect Flowchart.
The timing on these flowcharts is critical. Care
should be taken to ensure that, where a pause is
specified, it is followed as closely as possible. Do
not allow the microprocessor to service interrupts
that will upset the timing and do not abort the pro-
cedure before reaching the end. Chip Unprotect
can take several seconds and a user message
should be provided to show that the operation is
progressing.
Others = X
Others = X
Others = X
Others = X
A0-A20
IH
IH
, A6 = V
, A6 = V
IH
, A15 = V
IH
IH
IL
or V
, A9 = V
, A9 = V
IL
IH
ID
ID
,
,
DQ15A–1, DQ14-DQ0
Data Inputs/Outputs
Retry = XX00h
Retry = XX01h
Pass = XX01h
Pass = XX00h
X
X