VIPER22ADIP-E STMicroelectronics, VIPER22ADIP-E Datasheet
VIPER22ADIP-E
Specifications of VIPER22ADIP-E
VIPER22ADIP-E
Available stocks
Related parts for VIPER22ADIP-E
VIPER22ADIP-E Summary of contents
Page 1
... Automatic burst mode in low load condition. – Overvoltage protection in hiccup mode. ON/OFF 60kHz OSCILLATOR PWM S LATCH OVERTEMP DETECTOR BLANKING OVERVOLTAGE LATCH VIPer22ADIP VIPer22AS SO-8 DIP-8 ORDER CODES TUBE T&R 13TR VIPer22AS VIPer22AS - VIPer22ADIP DRAIN + _ 0.23 V 230 1 k SOURCE pin DD 1/15 ...
Page 2
... VIPer22ADIP / VIPer22AS PIN FUNCTION Name Power supply of the control circuits. Also provides a charging current during start up thanks to a high voltage current source connected to the drain. For this purpose, an hysteresis comparator monitors the V voltage and provides two thresholds Voltage value (typically 14.5V) at which the device starts switching and turns off the start up ...
Page 3
... D I =0.4A; T =100° =0.2A; V =300V (See fig. (See note 1) I =0.4A; V =300V (See fig. (See note 1) V =25V DS VIPer22ADIP / VIPer22AS Value Unit -0.3 ... 730 V -0.3 ... 400 V Internally limited A 0 ... 200 V 1.5 kV Internally limited C -40 to 150 C -55 to 150 C voltage has reached V ...
Page 4
... VIPer22ADIP / VIPer22AS ELECTRICAL CHARACTERISTICS (T SUPPLY SECTION Symbol Parameter Start Up Charging I DDch Current Start Up Charging I Current DDoff in Thermal Shutdown Operating Supply Current I DD0 Not Switching Operating Supply Current I DD1 Switching D Restart Duty Cycle RST V Undervoltage DD V DDoff Shutdown Threshold V V Start Up Threshold ...
Page 5
... Figure 1 : Rise and Fall Time 90 10% Figure 2 : Start Up VDD Current DD0 V DDhyst V V DDoff DDon I DDch Figure 3 : Restart Duty Cycle DDon V DDoff ------------------------- RST VIPer22A 100 kHz VIPer22ADIP / VIPer22AS << Coss VDD DRAIN 300V CONTROL SOURCE VDD DRAIN FB CONTROL SOURCE 2V VIPer22A 100V 5/15 ...
Page 6
... VIPer22ADIP / VIPer22AS Figure 4 : Peak Drain Current vs. Feedback Current Dpeak 1/F OSC I FBsd The drain current limitation is obtained for VFB = 0 V, and a negative current is drawn from the FB pin. See the Application section for further details. Figure 5 : Thermal Shutdown HYST DDon 6/15 t 18V ...
Page 7
... Figure 6 : Switching Frequency vs Temperature 1.01 1 0.99 0.98 0.97 -20 Figure 7 : Current Limitation vs Temperature 1.04 1.03 1.02 1.01 1 0.99 0.98 0.97 0.96 0.95 0.94 -20 Vdd = 10V ... 35V Temperature (°C) Vin = 100V Vdd = 20V Temperature (°C) VIPer22ADIP / VIPer22AS 100 120 100 120 7/15 ...
Page 8
... VIPer22ADIP / VIPer22AS Figure 8 : Rectangular U-I output characteristics for battery charger RECTANGULAR U-I OUTPUT CHARACTERISTIC A complete regulation scheme can achieve combined and accurate output characteristics. Figure 8 presents a secondary feedback through an optocoupler driven by a TSM101. This device offers two operational amplifiers and a voltage reference, thus allowing the regulation of both output voltage and current ...
Page 9
... S PWM Q LATCH R Figure 230 R2 t ONmin SOURCE -------------------------------------- - t ONmin -------------------------------------- - VIPer22ADIP / VIPer22AS < where I FB FBsd FBsd and I as shown on figure 10 lower than V DD DDon , the start up current source is DDon Transfer function FB I ...
Page 10
... VIPer22ADIP / VIPer22AS Figure 11 : Start Up Sequence DDon V DDoff tss OUT the regulation point where the secondary loop begins to send a current in the optocoupler. At this point, the converter enters a regulated operation where the FB pin receives the amount of current needed to deliver the right power on secondary side ...
Page 11
... TYP 0.65 b 0.35 b1 0. 4.8 5 1.27 e3 3.81 F 3 0.8 VIPer22ADIP / VIPer22AS inch MAX. MIN. TYP. 1.75 0.25 0.003 1.65 0.85 0.025 0.48 0.013 0.25 0.007 0.5 0.010 45 (typ.) 5 0.188 6.2 0.228 0.050 0.150 4 0.14 1.27 0.015 0.6 8 (max.) 1 ...
Page 12
... VIPer22ADIP / VIPer22AS Plastic DIP-8 MECHANICAL DATA DIM Package Weight 12/15 mm. MIN. TYP 0.38 2.92 3.30 0.36 0.46 1.14 1.52 0.20 0.25 9.02 9.27 7.62 7.87 6.10 6.35 2.54 7.62 2.92 3.30 Gr. 470 MAX. 5.33 4.95 0.56 1.78 0.36 10.16 8.26 7.11 10 ...
Page 13
... Tube length (± 0. (± 0.1) All dimensions are in mm 1.5 1.5 5.5 4.5 2 End Top No components cover 500mm min tape VIPer22ADIP / VIPer22AS 100 2000 532 3.2 6 0.6 REEL DIMENSIONS Base Q.ty 2500 Bulk Q.ty 2500 A (max) 330 B (min) 1.5 C (± -0) 12 ...
Page 14
... VIPer22ADIP / VIPer22AS A 14/15 DIP-8 TUBE SHIPMENT (no suffix) C Base Q.ty Bulk Q.ty Tube length (± 0. (± 0.1) All dimensions are in mm. 20 1000 532 8.4 11.2 0 ...
Page 15
... STMicroelectronics - Printed in ITALY- All Rights Reserved. Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - U.S.A. The ST logo is a trademark of STMicroelectronics STMicroelectronics GROUP OF COMPANIES http://www.st.com VIPer22ADIP / VIPer22AS 15/15 ...