LT1510IS8#TR Linear Technology, LT1510IS8#TR Datasheet - Page 13
![IC CHARGER BATT CONST V/I 8SOIC](/photos/6/62/66297/8-soic_05-08-1610_sml.jpg)
LT1510IS8#TR
Manufacturer Part Number
LT1510IS8#TR
Description
IC CHARGER BATT CONST V/I 8SOIC
Manufacturer
Linear Technology
Datasheet
1.LT1510CSPBF.pdf
(16 pages)
Specifications of LT1510IS8#TR
Function
Charge Management
Battery Type
Li-Ion, NiCd, NiMH
Voltage - Supply
6.2 V ~ 28 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
8-SOIC (0.154", 3.90mm Width)
Output Current
1.5A
Output Voltage
2 to 20V
Operating Supply Voltage (min)
7V
Operating Supply Voltage (max)
30V
Operating Temp Range
-40C to 85C
Package Type
SOIC N
Mounting
Surface Mount
Pin Count
8
Operating Temperature Classification
Industrial
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
APPLICATIONS
Example: V
Total power in the IC is:
Temperature rise will be (0.88W)(50 C/W) = 44 C. This
assumes that the LT1510 is properly heat sunk by con-
necting the four fused ground pins to the expanded traces
and that the PC board has a backside or internal plane for
heat spreading.
The P
diode D2 (see Figures 2 and 6 circuits) to a lower system
voltage (lower than V
Then,
For example, V
P
P
P
P
0.17 + 0.13 + 0.32+ 0.26 = 0.88W
P
P
DRIVER
BIAS
SW
SENSE
DRIVER
DRIVER
DRIVER
8 4
15
0 28 0 04 0 32
2
1 2
.
IN
3 5
10 10
7 5
.
term can be reduced by connecting the boost
= 15V, V
0 18 1 2
1 2 8 4
I
1 2
mA
•
BAT
X
.
2
mA
= 3.3V,
0 35 8 4
A
15
.
.
U
15
V
55 15
9
8 4
BAT
BAT
.
55
BAT
0 012 1 2
2
15 1 2 200
V
2
55 15
INFORMATION
) instead of V
.
1
1 5
.
U
V
= 8.4V, I
V
IN
3 3
X
0 26
mA
.
W
8 4
30
.
V
V
1
W
8 4
1
30
V
BAT
W
X
0 13
kHz
0 17
3 3
BAT
= 1.2A;
30
V
W
(see Figure 8).
W
U
0 045
W
The average I
Total board area becomes an important factor when the
area of the board drops below about 20 square inches. The
graph in Figure 9 shows thermal resistance vs board area
for 2-layer and 4-layer boards. Note that 4-layer boards
have significantly lower thermal resistance, but both types
show a rapid increase for reduced board areas. Figure 10
shows actual measured lead temperature for chargers
operating at full current. Battery voltage and input voltage
will affect device power dissipation, so the data sheet
power calculations must be used to extrapolate these
readings to other situations.
Vias should be used to connect board layers together.
Planes under the charger area can be cut away from the
rest of the board and connected with vias to form both a
P
DRIVER
V
X
Figure 9. LT1510 Thermal Resistance
60
55
50
45
40
35
30
25
V
X
VX
0 045
0
I
3 3
VX
S16, MEASURED FROM AIR AMBIENT
TO DIE USING COPPER LANDS AS
SHOWN ON DATA SHEET
required is:
L1
5
V
W
+
10
BOARD AREA (IN
Figure 8
14
D2
10 F
C1
15
mA
LT1510/LT1510-5
4-LAYER BOARD
2-LAYER BOARD
20
SW
BOOST
SENSE
2
25
)
LT1510
1510 F07
30
1510 F08
35
13