MAX17043G+T Maxim Integrated Products, MAX17043G+T Datasheet - Page 7

• Manufacturer Part Number: MAX17043G+T
• Description: IC 2-WIRE FG MODEL GAUGE LO BATT
• Manufacturer: Maxim Integrated Products
• Series: ModelGauge™r

Specifications of MAX17043G+T

• Function: Fuel, Gas Gauge/Monitor
• Battery Type: Lithium-Ion (Li-Ion)
• Voltage - Supply: 2.5 V ~ 4.5 V
• Operating Temperature: -20°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 8-TDFN Exposed Pad
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 90-2771G+BTR

When the battery is first inserted into the system, there
is no previous knowledge about the battery’s SOC. The
IC assumes that the battery has been in a relaxed state
for the previous 30min. The first A/D voltage measure-
ment is translated into a best “first guess” for the SOC.
Initial error caused by the battery not being in a relaxed
state fades over time, regardless of cell loading follow-
ing this initial conversion. Because the SOC determina-
tion is convergent rather than divergent (as in a
coulomb counter), this initial error does not have a long-
lasting impact.
A quick-start allows the MAX17043/MAX17044 to restart
fuel-gauge calculations in the same manner as initial
power-up of the IC. For example, if an application’s
power-up sequence is exceedingly noisy such that
excess error is introduced into the IC’s “first guess” of
SOC, the host can issue a quick-start to reduce the
error. A quick-start is initiated by a rising edge on the
QSTRT pin, or through software by writing 4000h to the
MODE register.
The MAX17043/MAX17044 have an interrupt feature
that alerts a host microprocessor whenever the cell's
state of charge, as defined by the SOC register, falls
below a predefined alert threshold set at address 0Dh
of the CONFIG register.
When an alert is triggered, the IC drives the ALRT pin to
logic-low and sets the ALRT bit in the CONFIG register
to logic 1. The ALRT pin remains logic-low until the host
software writes the ALRT bit to logic 0 to clear the inter-
rupt. Clearing the ALRT bit while SOC is below the alert
threshold does not generate another interrupt. The SOC
register must first rise above and then fall below the alert
threshold value before another interrupt is generated.
Table 1. Register Summary
ADDRESS
0Ch–0Dh
02h–03h
04h–05h
06h–07h
08h–09h
FEh–FFh
(HEX)
_______________________________________________________________________________________
COMMAND
REGISTER
VERSION
CONFIG
VCELL
MODE
SOC
Compact, Low-Cost 1S/2S Fuel Gauges
ALERT Interrupt
Reports 12-bit A/D measurement of battery voltage.
Reports 16-bit SOC result calculated by ModelGauge algorithm.
Sends special commands to the IC.
Returns IC version.
Battery compensation. Adjusts IC performance based on
application conditions.
Sends special commands to the IC.
IC Power-Up
Quick-Start
DESCRIPTION
Note that the alert function is not disabled at IC power-
up. If the first SOC calculation is below the threshold
setting, an interrupt is generated. Entering Sleep mode
does not clear the interrupt.
Holding both SDA and SCL logic-low forces the
MAX17043/MAX17044 into Sleep mode. While in Sleep
mode, all IC operations are halted and power drain of
the IC is greatly reduced. After exiting Sleep mode,
fuel-gauge operation continues from the point it was
halted. SDA and SCL must be held low for at least 2.5s
to guarantee transition into Sleep mode. Afterwards, a
rising edge on either SDA or SCL immediately transi-
tions the IC out of Sleep mode.
Alternatively, Sleep mode can be entered by setting the
SLEEP bit in the CONFIG register to logic 1 through I
communication. If the SLEEP bit is set to logic 1, the
only way to exit Sleep mode is to write SLEEP to logic 0
or power-on reset the IC.
Writing a value of 5400h to the COMMAND register caus-
es the MAX17043/MAX17044 to completely reset as if
power had been removed. The reset occurs when the last
bit has been clocked in. The IC does not respond with an
I
All host interaction with the MAX17043/MAX17044 is
handled by writing to and reading from register loca-
tions. The MAX17043/MAX17044 have six 16-bit regis-
ters: SOC, VCELL, MODE, VERSION, CONFIG, and
COMMAND. Register reads and writes are only valid if
all 16 bits are transferred. Any write command that is
terminated early is ignored. The function of each regis-
ter is described as follows. All remaining address loca-
tions not listed in Table 1 are reserved. Data read from
reserved locations is undefined.
with Low-Battery Alert
2
C ACK after this command sequence.
Power-On Reset (POR)
WRITE
READ/
R/W
W
W
R
R
R
Sleep Mode
Registers
DEFAULT
971Ch
(HEX)
—
—
—
—
—
2
7
C