ABMS-A-C Panduit Corp, ABMS-A-C Datasheet - Page 3
ABMS-A-C
Manufacturer Part Number
ABMS-A-C
Description
TIE HOLDER W/ADHESIVE
Manufacturer
Panduit Corp
Type
Dual Openingr
Specifications of ABMS-A-C
Mounting Type
Screw, #6, Adhesive
Size / Dimension
1.13" L x 1.13" W x 0.25" H (28.7mm x 28.7mm x 6.4mm)
Color
Natural
Mounting Method
Adhesive
Size
1.13 in x 1.13 in x 0.21 in
Height
0.21 in
Length
1.13 in
Maximum Bundle Diameter
4.8 mm
Tensile Strength
0.6 lbs
Where Used
Clean, dry, smooth, grease free surfaces
Width
1.13 in
Application
For indoor use
Protection Class
Mount, Cable Tie
Size, Thread
M3
Special Features
Adhesive Backed
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With/related Products
M, I, S Ties
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
298-1117
applied to clean, dry, grease-free surfaces. It is
Surface Preparation
For best results, PANDUIT adhesive mounts should be
recommended that for each individual application a
solvent or cleanser be used to thoroughly prepare the
surface for mount installation to obtain best results. The
following are recommended guidelines:
1. For rubber and acrylic based foam tape adhesives,
2. For epoxy type adhesives, especially masonry
Proper Installation Techniques
Pressure Sensitive Adhesive Mounts
For proper installation of adhesive mounts with foam tape, simply remove the release liner from foam
adhesive and place the mount in the desired location. Apply firm pressure to the mount to insure proper
adhesion. Avoid touching the adhesive prior to placing the mount on the surface.
Product Information*
The following descriptions refer to the adhesive mount information chart which follows on the next page.
Part Number: The package code suffix must be added to each part number to determine quantity per
package. Refer to the current catalog or price sheets for suffix designations.
Dimensions: Given are over-all mount with adhesive dimensions; L = Base Length, W = Base Width,
H = Height
Adhesive Type: Refer to the adhesive information section for more details.
Cable Ties: PANDUIT
Maximum Static Load: Values given are for shear and/or normal loading and optimal adhesion between
surfaces.
Normal Service Temperature Range: Given are the continuous use temperature ranges.
Maximum Intermittent Temperature: Given are values for time periods of less than two hours.
Minimum Installation Temperature: Values given are for the substrate temperature and/or ambient
temperature.
Dwell Time: Values given are time to allow mount to set before loading. Dwell time is increased when the
installation temperature is below minimum.
Mount Material: Given for each type of mount.
Screw Hole Size: Values are specified when applicable.
U.L. Recognized: Tested and recognized under the Underwriters’ Laboratories, Inc., component recognition
program.
*All product information is recommended values based on results of controlled laboratory tests. For specific applications, individual testing
prior to extensive use is suggested.
isopropyl alcohol may be used on most surfaces.
surfaces, be sure to clean all loose particles away
before mount installation. Some surface abrasion is
recommended to achieve maximum strength. A light
rubbing with medium grit emery cloth or sandpaper
is best. Wash after abrading.
Clean surface with a
clean cloth and
isopropyl alcohol.
Selection and Use of Adhesive Mounts
®
mounts are designed to use PANDUIT
Allow surface to air dry.
Remove the release
liner, being caeful not
to touch the adhesive.
Mount Spacing
To determine the number of mounts to use in a given
application, the following formula can be used as a
guideline:
Cable or weight (lbs./ft.)
Static Load rating of Mount (lbs/mt.)
(See pages 4-6 for static load rating of mounts)
For specific applications we recommend individual
testing prior to production use.
Apply full thumb
pressure for at least 5
seconds.
®
cable ties. The respective size of tie is given.
Allow mount to
properly dwell.
ELECTRICAL GROUP
= Spacing
Mounts
Ft.
3