CS5461A-ISZ Cirrus Logic Inc, CS5461A-ISZ Datasheet - Page 36

• Manufacturer Part Number: CS5461A-ISZ
• Description: IC ENERGY METERING 1PHASE 24SSOP
• Manufacturer: Cirrus Logic Inc

Specifications of CS5461A-ISZ

• Package / Case: 24-SSOP
• Input Impedance: 30 KOhm
• Measurement Error: 0.1%
• Voltage - I/o High: 0.8V
• Voltage - I/o Low: 0.2V
• Current - Supply: 2.9mA
• Voltage - Supply: 4.75 V ~ 5.25 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Meter Type: Single Phase
• Output Voltage Range: 2.4 V to 2.6 V
• Input Voltage Range: 2.4 V to 2.6 V
• Input Current: 25 nA
• Power Dissipation: 500 mW
• Operating Temperature Range: - 40 C to + 85 C
• Mounting Style: SMD/SMT
• Input Voltage: 5V
• Supply Voltage Range: 3.135V To 5.25V
• No. Of Pins: 24
• Filter Terminals: SMD
• No. Of Channels: 2
• Ic Generic Number: 5461
• Output Current Max: 1µA
• Rohs Compliant: Yes
• Leaded Process Compatible: No
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 598-1552 - BOARD EVAL & SOFTWARE CS5461A
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 598-1095-5

component present in the system during conversion
commands.
7.1.2.2 AC Offset Calibration Sequence
Corresponding offset registers I
should be cleared prior to initiating AC offset calibra-
tions. Initiate an AC offset calibration. The AC offset reg-
isters are updated with an offset value that reflects the
RMS output level. Upon completion of the AC offset cal-
ibration the AC offset is stored in the corresponding AC
offset register. The AC offset register value is subtract-
ed from each successive V
7.1.3 Gain Calibration Sequence
When performing gain calibrations, a reference signal
should be applied to the VIN± pins of the voltage and
IIN± pins of the current channels that represents the de-
sired maximum signal level.
setup for gain calibration.
For gain calibrations, there is an absolute limit on the
RMS voltage levels that are selected for the gain-cali-
bration input signals. The maximum value that the gain
registers can attain is 4. Therefore, if the signal level of
the applied input is low enough that it causes the
CS5461A to attempt to set either gain register higher
than 4, the gain calibration result will be invalid and all
CS5461A results obtained while performing measure-
ments will be invalid.
If the channel gain registers are initially set to a gain oth-
er then 1.0, AC gain calibration should be used.
7.1.3.1 AC Gain Calibration Sequence
The corresponding gain register should be set to 1.0,
unless a different initial gain value is desired. Initiate an
AC gain calibration. The AC gain calibration algorithm
computes the RMS value of the reference signal applied
to the channel inputs. The RMS register value is then di-
vided into 0.6 and the quotient is stored in the corre-
sponding
measurement will be multiplied by its corresponding AC
gain value.
36
R eference
Signal
CM + -
Figure 11. System Calibration of Gain
+
-
External
Connections
gain
IN+
IN-
register.
RMS
Figure 11
+
-
and I
Each
XG AIN
ACoff
RMS
shows the basic
and/or V
instantaneous
calculation.
+
-
ACoff
A typical rms calibration value which allows for reason-
able over-range margin would be 0.6 or 60% of the volt-
age and current channel’s maximum input voltage level.
Two examples of AC gain calibration and the updated
digital output codes of the channel’s instantaneous data
registers are shown in Figures 12 and 13. Figure 13
shows that a positive (or negative), DC-level signal can
be used even though an AC gain calibration is being ex-
Figure 13. Another Example of AC Gain Calibration
Sinewave
Sinewave
DC Signal
DC Signal
SIGNAL
SIGNAL
SIGNAL
After AC Gain Calibration (Vgain Register changed to approx. 0.65217)
SIGNAL
After AC Gain Calibration (Vgn Register changed to approx. 0.9223)
INPUT
INPUT
INPUT
INPUT
Figure 12. Example of AC Gain Calibration
-250 mV
-250 mV
250 mV
230 mV
-230 mV
-250 mV
Before AC Gain Calibration (Vgain Register = 1)
-230 mV
-250 mV
250 mV
230 mV
250 mV
230 mV
250 mV
230 mV
0 V
0 V
0 V
0 V
Before AC Gain Calibration (Vgn Register = 1)
V
RMS
V
V
V
RMS
Register =
RMS
RMS
Register = 0.600000
Register = 0.600000
Register =
230
/
√2
x
250
230
1
/
250
= 0.92
≈ 0.65054
-0.84853
-0.92231
CS5461A
-1.0000...
0.92231
0.84853
0.9999...
-0.92
0.92
Instantaneous Voltage
Instantaneous Voltage
-0.65217
-1.0000...
0.65217
0.9999...
0.92
0.6000
Register Values
Instantaneous Voltage
Register Values
Instantaneous Voltage
Register Values
DS661F2
Register Values