MCP3909-I/SS Microchip Technology, MCP3909-I/SS Datasheet - Page 26

• Manufacturer Part Number: MCP3909-I/SS
• Description: IC POWER METERING-1 PHASE 24SSOP
• Manufacturer: Microchip Technology

Specifications of MCP3909-I/SS

• Package / Case: 24-SSOP (0.200", 5.30mm Width)
• Input Impedance: 390 KOhm
• Measurement Error: 0.1%
• Voltage - I/o High: 2.4V
• Voltage - I/o Low: 0.85V
• Current - Supply: 2.3mA
• Voltage - Supply: 4.5 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Meter Type: Single Phase
• Operating Temperature Range: - 40 C to + 85 C
• Mounting Style: SMD/SMT
• Supply Voltage Range: 4.5V To 5.5V
• Digital Ic Case Style: SSOP
• No. Of Pins: 24
• Interface Type: Serial, SPI
• Supply Voltage Max: 5.5V
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: MCP3909EV-MCU16 - EVALUATION BOARD FOR MCP3909MCP3909RD-3PH1 - REF DESIGN MCP3909 3PH ENGY MTR
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

MCP3909
FIGURE 5-3:
5.2
The MCP3909 devices contains three different serial
modes with data presented in 2's complement coding.
• Multiplier Output
• Dual Channel Output
• Filter Input
TABLE 5-1:
DS22025B-page 26
Note 1:
1 0 1 0 0 0 0 1
1 0 1 0 1 0 0 1
1 0 1 0 0 1 0 0
1 0 1 0 1 1 0 0
1 0 1 0 1 0 1 0
1 0 1 0 1 1 1 0
1 0 1 0 0 0 1 0
1 0 1 0 0 1 1 0
F2 / SCK
F1 / SDI
F0 / CS
MCLR
Command
D7......D0
Serial Mode Entry Codes
The active power frequency outputs F
Leaving the SDI (F1) and CS (F0) pins at a known state after serial communication will control the
frequency selection. The HPF pin controls the state of the HPF for the multiplier mode output and the
output pulses from the active power D to F block.
ENTRY CODES
Dual Functionality Pin Serial Mode Entry Protocol.
Dual Channel Output Post HPF1
Dual Channel Output Pre HPF1
t
WINSET
Multiplier Output
Multiplier Output
Serial Mode
Filter Input
Filter Input
Filter Input
Filter Input
t
1
D7 D6
WINDOW
OUT0
2
, F
3
D5 D4
OUT1
4
, and HF
After entering any of these modes the active power
calculation block is still functional and presents output
pulses on F
the F2, F1, F0 output frequency selection constant can
be changed with multiple command bytes for serial
mode entry.
The command bytes to enter these modes are
described in
D3 D2 D1 D0
5
Internal State of F2, F1, F0 Constants Frequency
6
OUT
F2
0
1
0
7
1
1
1
0
0
Selection During Serial Mode
remain active after serial mode entry.
OUT0
Table
8
, F
5-1.
OUT1
© 2009 Microchip Technology Inc.
, and HF
F1 pin
F1 pin
F1 pin
F1 pin
F1
0
1
0
1
OUT
. For this reason,
(1)
F0 pin
F0 pin
F0 pin
F0 pin
F0
1
1
1
1