MIC2590B-2YTQ TR Micrel Inc, MIC2590B-2YTQ TR Datasheet - Page 20
![IC PCI HOT PLUG CTLR DUAL 48TQFP](/photos/6/84/68454/576-48-tqfp_sml.jpg)
MIC2590B-2YTQ TR
Manufacturer Part Number
MIC2590B-2YTQ TR
Description
IC PCI HOT PLUG CTLR DUAL 48TQFP
Manufacturer
Micrel Inc
Type
Hot-Swap Controllerr
Datasheet
1.MIC2590B-2YTQ.pdf
(23 pages)
Specifications of MIC2590B-2YTQ TR
Applications
PCI, PCI-X
Internal Switch(s)
No
Voltage - Supply
3.3V, 5V, ±12V
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
48-TQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
MIC2590B-2YTQTR
MIC2590B-2YTQTR
MIC2590B-2YTQTR
MOSFET Transient Thermal Issues
Having chosen a MOSFET that will withstand the imposed
voltage stresses, and be able to handle the worst-case
continuous I
remains only to verify the MOSFET’s ability to handle
short-term
overheating. Here, nature and physics work in our favor: a
Micrel, Inc.
September 2008
2. Since the rating for the part is given as “for
3. Airflow, if available, works wonders. This is not
4. Although it seems a rather unsatisfactory
the MOSFET drain.
10seconds,”
temperature by 35°C. This is the standard good
practice derating of 25°C, plus another 10°C to
allow for the time element of the specification.
the place for a dissertation on how to perform
airflow calculations, but even a few LFM (linear
feet per minute) of air will cool a MOSFET down
dramatically. If you can position the MOSFET(s)
in question near the inlet of a power supply’s fan,
or the outlet of a processor’s cooling fan, that’s
always a good free ride.
statement, the best test of a surface-mount
MOSFET for an application (assuming the above
tips show it to be a likely fit) is an empirical one.
The ideal evaluation is in the actual layout of the
expected final circuit, at full operating current. The
use of a thermocouple on the drain leads, or in
infrared pyrometer on the package, will then give
a reasonable idea of the device’s junction
temperature.
2
R power dissipation which it will see, it
overload
0.01
0.1
2
1
10
derate
-4
Duty Cycle = 0.5
0.2
0.1
0.05
0.02
power
Figure 10. Si4430DY MOSFET Transient Thermal Impedance Curve
the
10
dissipation
-3
maximum
Normalized Thermal Transient Imperance, Juction-to-Ambient
Single Pulse
10
-2
junction
without
Square Wave Pulse Duration (sec)
10
-1
20
MOSFET can handle a much higher pulsed power without
damage than its continuous dissipation ratings would
imply. The reason for this is that, like everything else,
semiconductor devices (silicon die, lead frames, etc.)
have thermal inertia. This is easily understood by all of us
who have stood waiting for a pot of water to boil.
In terms related directly to the specification and use of
power MOSFETs, this is known as “transient thermal
impedance.” Almost all power MOSFET data sheets give
a Transient Thermal Impedance Curve, which is a handy
tool for making sure that you can safely get by with a less
expensive MOSFET than you thought you might need.
For example, take the case where t
has been set to 50ms, I
threshold is 50mV nominal, and the fast-trip threshold is
100mV. If the output is connected to a 0.60Ω load, the
output current from the MOSFET for the slot in question
will be regulated to 5.0A for 50ms before the part’s circuit
breaker trips. During that time, the dissipation in the
MOSFET is given by:
Wow! Looks like we need a really hefty MOSFET to
withstand just this unlikely—but plausible enough to
protect against—fault condition. Or do we? This is where
the transient thermal impedance curves become very
useful. Figure 10 shows those curves for the Vishay
(Siliconix) Si4430DY, a commonly used SO-8 power
MOSFET.
1
P
P
MOSFET
=
E
×
I
E
=
MOSFET
(
10
2V
1. Duty Cycle, D =
2. Per Unit Base = R
3. T
4. Surface Mounted
Notes:
P
DM
JM
×
LOAD(CONT,MAX)
– T
5A
t
1
A
=
= P
t
)
2
[
5V
=
DM
10W
Z
100
qJA
−
t
t
1
2
qJA
(t)
5A(0.6ΩA
= 67°C/W
FLT
for
is 5.0A, the slow-trip
for the 5V supply
50ms
600
M9999-091808
]
=
MIC2590B
2V