MAX8678ETE+ Maxim Integrated Products, MAX8678ETE+ Datasheet - Page 8

• Manufacturer Part Number: MAX8678ETE+
• Description: IC LED DRVR WHITE BCKLGT 16-TQFN
• Manufacturer: Maxim Integrated Products
• Type: Backlight, White LEDr

Specifications of MAX8678ETE+

• Constant Current: Yes
• Topology: PWM, Switched Capacitor (Charge Pump)
• Number Of Outputs: 4
• Internal Driver: Yes
• Type - Primary: Backlight
• Type - Secondary: White LED
• Frequency: 1MHz
• Voltage - Supply: 2.7 V ~ 5.5 V
• Voltage - Output: 5V
• Mounting Type: Surface Mount
• Package / Case: 16-TQFN Exposed Pad
• Operating Temperature: -40°C ~ 85°C
• Current - Output / Channel: 24mA
• Internal Switch(s): Yes
• Low Level Output Current: 0.6 A
• High Level Output Current: 1.6 A
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Supply Current: 3 mA
• Maximum Power Dissipation: 1398 mW
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Efficiency: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

The charge pump drives up to four white LEDs with
regulated constant current for displaying backlight
applications. By utilizing an adaptive charge pump and
extremely low-dropout current regulators, it achieves
high efficiency over the full 1-cell lithium ion (Li+) bat-
tery input-voltage range. Fixed frequency of 1MHz
switching allows for tiny external components. The reg-
ulation scheme is optimized to ensure low EMI and low
input ripple.
When the supply voltage is sufficient to drive the LEDs,
the charge pump is turned off to minimize the input
supply current and the LED currents are linearly regu-
lated. When the supply voltage is insufficient to drive
the LEDs at the set current, the charge pump is
enabled, creating a negative voltage at NEG and allow-
ing the LED_ outputs to pull below ground to maintain
the set LED current.
The MAX8678 internally generates a PWM signal to
obtain higher resolution at lower currents. As the I
setting is below 6.4mA, the IC adjusts I
and the duty cycle is controlled by the PWM signal. The
frequency of the PWM dimming signal is set at 1kHz
with a minimum duty cycle of 1/16 to avoid the LED
flicking effect to human eyes. Table 1 shows the current
level and the corresponding duty cycle.
The MAX8678 LED driver features a low-power shut-
down mode for reduced current consumption. Hold
ENLED low for 3.2ms to enter shutdown mode. This dis-
ables the charge pump and the LED current drivers.
When initially powering the MAX8678, or when starting
up from shutdown mode, a soft-start feature prevents
input current overshoot. See the startup waveforms in
the Typical Operating Characteristics section.
White LED Charge Pump with
1.1W Audio Amplifier
Figure 2. Serial-Pulse Dimming
8
INTERNAL
CURRENT
SETTING
_______________________________________________________________________________________
ENLED
I
LED_
OFF
OFF
1
24.0mA 22.4mA 20.8mA 19.2mA
t
HI
2
Adaptive Charge-Pump Modes
t
LO
3
Soft-Start and Shutdown
Low LED Current Levels
LED Charge Pump
4
t
3.2ms
HOLD
LED
DC current,
19.2mA
1
LED
24.0mA
2
22.4mA 20.8mA
The MAX8678 includes a serial-pulse logic interface for
on/off and dimming of the backlight. The dimming
range is pseudo-logarithmic from 24mA to 0.1mA in 31
steps. Driving ENLED high turns on the IC and sets the
internal register to 24.0mA. To dim the MAX8678, pulse
ENLED low (500ns to 500µs pulse width). Each rising
edge sets the LED current setting as shown in Table 2.
Once the desired setting is reached, hold ENLED high
for at least 3.2ms to set the internal register and the
LED current changes. To set a new current level, repeat
the previous sequence from the beginning.
To turn off the LEDs, hold ENLED low for at least 3.2ms.
Figure 2 shows a timing diagram for ENLED.
If dimming control is not required, ENLED works as a
simple on/off logic control. Drive ENLED high for at
least 3.2ms to enable the LEDs, or drive ENLED low for
at least 3.2ms for shutdown. The LED driver operates at
100% brightness under or OFF under these conditions.
Table 1. Internal PWM Duty Cycle vs. LED
Set Current
3
(mA)
I
LED
6.4
5.6
4.8
4.0
3.2
2.8
2.4
2.0
1.6
1.4
13
5.6mA
DUTY CYCLE
Serial-Pulse Dimming Control (ENLED)
14
(n/16)
16
14
12
10
16
14
12
10
16
14
4.8mA
3.2ms
t
HOLD
(mA)
I
4.8mA
LED
1.2
1.0
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
3.2ms
t
SHDN
t
t
HI
LO
= 500ns TO 500μs
= 500ns TO 500μs
DUTY CYCLE
OFF
(n/16)
12
10
8
7
6
5
4
3
2
1
OFF