MAX16801AEUA+ Maxim Integrated Products, MAX16801AEUA+ Datasheet - Page 10
![IC LED DRIVER HIGH BRIGHT 8-MSOP](/photos/1/39/13936/406-8-msop_sml.jpg)
MAX16801AEUA+
Manufacturer Part Number
MAX16801AEUA+
Description
IC LED DRIVER HIGH BRIGHT 8-MSOP
Manufacturer
Maxim Integrated Products
Type
HBLED Driverr
Datasheet
1.MAX16802BEUA.pdf
(16 pages)
Specifications of MAX16801AEUA+
Constant Current
Yes
Topology
Flyback, PWM, SEPIC, Step-Down (Buck), Step-Up (Boost)
Number Of Outputs
1
Internal Driver
No
Type - Primary
Backlight
Type - Secondary
High Brightness LED (HBLED), RGB
Frequency
230kHz ~ 290kHz
Voltage - Supply
85 V ~ 265 V
Mounting Type
Surface Mount
Package / Case
8-MSOP, Micro8™, 8-uMAX, 8-uSOP,
Operating Temperature
-40°C ~ 85°C
Current - Output / Channel
3A
Internal Switch(s)
No
Low Level Output Current
500 uA (Min)
High Level Output Current
500 uA (Min)
Operating Supply Voltage
10.8 V to 24 V
Maximum Supply Current
2.5 mA
Maximum Power Dissipation
362 mW
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
Minimum Operating Temperature
- 40 C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Voltage - Output
-
Efficiency
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
The IN bypass capacitor C1 supplies current immedi-
ately after wake-up (Figure 5). The size of C1 and the
connection configuration of the tertiary winding deter-
mine the number of cycles available for startup. Large
values of C1 increase the startup time but also supply
gate charge for more cycles during initial startup. If the
value of C1 is too small, V
because NDRV does not have enough time to switch
and build up sufficient voltage across the tertiary wind-
ing that powers the device. The device goes back into
UVLO and does not start. Use low-leakage capacitors
for C1 and C2.
Assuming that offline LED drivers keep typical startup
times to less than 500ms even in low-line conditions
(85VAC input for universal offline applications), size the
startup resistor R1 to supply both the maximum startup
bias of the device (90µA, worst case) and the charging
current for C1 and C2. The bypass capacitor C2 must
charge to +9.5V and C1 to +24V, all within the desired
time period of 500ms.
Because of the internal 60ms soft-start time of the
MAX16801, C1 must store enough charge to deliver
current to the device for at least this much time. To cal-
culate the approximate amount of capacitance
required, use the following formula:
where I
after startup (1.4mA), Q
Q1, f
(262kHz), V
(11.9V) and t
For example:
Choose the 15µF standard value.
Offline and DC-DC PWM Controllers for
High-Brightness LED Drivers
10
Brightness LED Drivers Using MAX16801
______________________________________________________________________________________
SW
Startup Time Considerations for High-
IN
is the MAX16801’s switching frequency
Ig
C
is the MAX16801’s internal supply current
1
HYST
SS
=
=
(
1 4
is the internal soft-start time (60ms).
(
Applications Information
8
.
nC
I
C
g
mA
is the bootstrap UVLO hysteresis
1
=
) (
=
×
Q
+
(
I
gtot
IN
262
gtot
2 1
(
12
.
+
V
mA
×
HYST
kHz
V
is the total gate charge for
I
g
)
f
SW
)
)
IN
)
×
( )
t
(
SS
=
60
drops below +9.7V
2 1
ms
.
mA
)
=
17 5
.
µ
F
Assuming C1 > C2, calculate the value of R1 as follows:
where V
the application, V
level (+23.6V, max), and I
at startup (90µA, max).
For example, for the minimum AC input of 85V:
Choose the 120kΩ standard value.
Choose a higher value for R1 than the one calculated
above if longer startup time can be tolerated in order to
minimize power loss on this resistor.
The above startup method is applicable to a circuit sim-
ilar to the one shown in Figure 5. In this circuit, the ter-
tiary winding has the same phase as the output
windings. Thus, the voltage on the tertiary winding at
any given time is proportional to the output voltage and
goes through the same soft-start period as the output
voltage. The minimum discharge voltage of C1 from
+22V to +10V must be greater than the soft-start time of
60ms.
Another method of bootstrapping the circuit is to have a
separate bias winding than the one used for regulating
the output voltage and to connect the bias winding so
that it is in phase with the MOSFET ON time (see Figure
9). In this case, the amount of capacitance required is
much smaller.
However, in this mode, the input voltage range has to
be less than 2:1. Another consideration is whether the
bias winding is in phase with the output. If so, the LED
driver circuit hiccups and soft-starts under output short-
circuit conditions. However, this property is lost if the
bias winding is in phase with the MOSFET ON time.
IN(MIN)
I
R
C1
1
=
=
I
R
(
C
(
1
0 72
is the minimum input supply voltage for
1
24
.
=
120
SUVR
=
(
V
500
V
mA
)
SUVR
(
V
V
×
500
IN MIN
ms
(
I
−
15
+
(
C
is the bootstrap UVLO wake-up
1
(
ms
)
START
2 2 4
µF
90
×
+
)
C
)
V
µ
)
I
1
−
A
START
=
)
0 72
)
V
is the IN supply current
.
=
SUVR
119
mA
k
Ω