MAX8648ETE+ Maxim Integrated Products, MAX8648ETE+ Datasheet - Page 8
![IC LED DRVR WT/RGB BCKLGT 16TQFN](/photos/6/66/66625/16-tqfn_exp_pad_21-0136_sml.jpg)
MAX8648ETE+
Manufacturer Part Number
MAX8648ETE+
Description
IC LED DRVR WT/RGB BCKLGT 16TQFN
Manufacturer
Maxim Integrated Products
Type
Backlight, White LED, RGB (Serial Interface)r
Datasheet
1.MAX8647ETE.pdf
(15 pages)
Specifications of MAX8648ETE+
Constant Current
Yes
Topology
PWM, Switched Capacitor (Charge Pump)
Number Of Outputs
6
Internal Driver
Yes
Type - Primary
Backlight
Type - Secondary
RGB, White LED
Frequency
1MHz
Voltage - Supply
1.7 V ~ 5.5 V
Voltage - Output
5V
Mounting Type
Surface Mount
Package / Case
16-TQFN Exposed Pad
Operating Temperature
-40°C ~ 85°C
Current - Output / Channel
24mA
Internal Switch(s)
Yes
Operating Supply Voltage
2.7 V to 5.5 V
Maximum Supply Current
1.6 mA
Maximum Power Dissipation
1667 mW
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
Minimum Operating Temperature
- 40 C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Efficiency
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Ultra-Efficient Charge Pumps for
Six White/RGB LEDs in 3mm x 3mm Thin QFN
The MAX8647/MAX8648 have an inverting charge
pump and six current regulators capable of 24mA each
to drive six white LEDs or two sets of RGB LEDs. The
current regulators are matched to within ±0.4% (typ)
providing uniform white LED brightness for LCD back-
light applications. To maximize efficiency, the current
regulators operate with as little as 0.15V voltage drop.
Individual white LED current regulators conduct current
to GND or NEG to extend usable battery life. In the
case of mismatched forward voltage of white LEDs,
only the white LEDs requiring higher voltage are
switched to pull current to NEG instead of GND, further
raising efficiency and reducing battery current drain.
When V
white LED plus the 0.15V headroom of the current regu-
lator, the LED current returns through GND. If this con-
dition is satisfied for all six white LEDs, the charge
pump remains inactive. When the input voltage drops
so that the current-regulator headroom cannot be main-
tained for any of the individual white LEDs, the inverting
charge pump activates and generates a voltage on the
NEG pin that is no greater than 5V below V
rent regulator contains circuitry that detects when it is
in dropout and switches that current-regulator return
path from GND to NEG. Since this is done on an LED-
by-LED basis, the LED current is switched for only the
individual LED requiring higher voltage, thus minimizing
power consumption.
The MAX8647/MAX8648 internally generate a PWM sig-
nal to obtain higher resolution at lower currents. See
Single-Wire Pulse Dimming in the Typical Operating
Characteristics section. As the I
6.4mA, the IC adjusts not only I
duty cycle is controlled by the PWM signal. The fre-
quency of the PWM dimming signal is set at 1kHz with
a minimum duty cycle of 1/16 to avoid the LED flicking
effect to human eyes. Table 1 shows the current level
and the corresponding duty cycle.
An I
MAX8647 to control the LEDs. The serial interface
consists of a serial-data line (SDA) and a serial-clock
line (SCL). Standard I
8
_______________________________________________________________________________________
2
C 2-wire serial interface is provided on the
IN
is higher than the forward voltage of the
Current-Regulator Switchover
Detailed Description
I
2
Low LED Current Levels
2
C write-byte commands are
C Interface (MAX8647)
LED
LED
DC current, but the
setting is below
IN
. Each cur-
used. Figure 2 shows a timing diagram for the I
tocol. The MAX8647 is a slave-only device, relying
upon a master to generate a clock signal. The master
(typically a microprocessor) initiates data transfer on
the bus and generates SCL to permit data transfer. A
master device communicates with the MAX8647 by
transmitting the proper 8-bit address (0x9A) followed
by the 8-bit control byte. Each 8-bit control byte con-
sists of a 3-bit command code and 5 bits of data (Table
1). Each transmit sequence is framed by a START (A)
condition and a STOP (L) condition (Figure 2). Each
word transmitted over the bus is 8 bits long and is
always followed by an ACKNOWLEDGE CLOCK
PULSE (K). The power-on default settings for D4 to D0
are all 0, which indicates that all LED_ are off.
When the LEDs are enabled by driving EN_ high, the
MAX8648 ramps LED current to 24mA. Dim the LEDs
by pulsing EN_ low (1µs to 500µs pulse width). Each
pulse reduces the LED current based on the LED dim-
ming table, Table 3. After the current reaches 0.1mA,
the next pulse restores the current to 24mA. Figure 3
shows a timing diagram for EN_. ENA controls LED1,
LED2, and LED3. ENB controls LED4 and LED5. ENC
controls LED6.
If dimming control is not required, EN_ work as simple
100% brightness or off controls. Drive EN_ high to enable
the LEDs, or drive EN_ low to disable. The IC is shut-
down when all three EN_ are low for 4ms or longer.
Table 1. Internal PWM Duty Cycle vs. LED
Set Current
Serial-Pulse Dimming Control (MAX8648)
(mA)
I
LED
6.4
5.6
4.8
4.0
3.2
2.8
2.4
2.0
1.6
1.4
DUTY CYCLE
(n/16)
16
14
12
10
16
14
12
10
16
14
(mA)
I
LED
1.2
1.0
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
DUTY CYCLE
(n/16)
12
10
2
8
7
6
5
4
3
2
1
C pro-