MAX16816ATJ+ Maxim Integrated Products, MAX16816ATJ+ Datasheet - Page 9

• Manufacturer Part Number: MAX16816ATJ+
• Description: IC LED DRIVR HIGH BRIGHT 32-TQFN
• Manufacturer: Maxim Integrated Products
• Type: HBLED Driverr

Specifications of MAX16816ATJ+

• Topology: PWM, SEPIC, Step-Down (Buck), Step-Up (Boost)
• Number Of Outputs: 1
• Internal Driver: Yes
• Type - Primary: Automotive
• Type - Secondary: High Brightness LED (HBLED)
• Frequency: 125kHz ~ 500kHz
• Voltage - Supply: 5.5 V ~ 76 V
• Mounting Type: Surface Mount
• Package / Case: 32-TQFN Exposed Pad
• Operating Temperature: -40°C ~ 125°C
• Internal Switch(s): Yes
• Efficiency: 90%
• Low Level Output Current: 76 mA
• High Level Output Current: 67 mA
• Operating Supply Voltage: 5.5 V to 76 V
• Maximum Supply Current: 4.5 mA
• Maximum Power Dissipation: 2758 mW
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Voltage - Output: -
• Current - Output / Channel: -
• Lead Free Status / Rohs Status: Details

ELECTRICAL CHARACTERISTICS
(V
unless otherwise noted.)
Note 1: Dropout voltage is defined as the input to output differential voltage at which the output voltage drops 100mV below its nom-
Note 2: V
Note 3: Minimum pulse width required to guarantee proper dimming operation.
Note 4: FAULT multiplexes a programming interface and fault indication functionality. At power-up initialization, an internal timer
Note 5: Not production tested. Guaranteed by design.
Note 6: Recovery time is the time required for FAULT to be pulled high by the internal 10kΩ resistor.
CC
26
25
24
23
22
21
20
19
18
= V
-60
inal value measured at output.
- V
response of the LED current-sense circuitry, resulting in current overshoot. To ensure proper operation, connect a 0.1µF
capacitor from CLMP to LO.
enables FAULT and two programming passcodes must be entered within the programming slot to enter programming
mode. If the programming passcodes are not received correctly within the programming slot, FAULT goes back towards
fault indication. Cycling power to the device is required to re-attempt entry into programming mode.
UVEN
-40 -20 0
CLMP_TH
LO
) to drive a FET. V
SHUTDOWN CURRENT
= 14V, C
vs. TEMPERATURE
TEMPERATURE (°C)
determines the voltage necessary to operate the current-sense amplifier. The DIM driver requires 2.5V for (V
20
_______________________________________________________________________________________
40 60
REG1
Programmable Switch-Mode LED Driver
with Analog-Controlled PWM Dimming
= 1µF, C
80
100
HI
120
is typically one diode drop above V
REG2
140
= 10µF, C
4.0
3.8
3.6
3.4
3.2
3.0
2.8
2.6
-60
CLMP
-40
-20
= 0.1µF, R
OPERATING CURRENT
vs. TEMPERATURE
0
TEMPERATURE (°C)
20
40
CS
Typical Operating Characteristics
60
= 0.1Ω, Binning adjustment register is ‘0000’, T
DGT AND DRV
NOT SWITCHING
80
CLMP
100
. A large capacitor connected to V
120
140
600
550
500
450
400
350
300
250
200
-60
-40 -20 0
vs. TEMPERATURE
OUTPUT CURRENT
TEMPERATURE (°C)
R
R
CS
CS
20
= 0.2Ω
= 0.3Ω
40 60
CLMP
A
80
= +25°C,
slows the
100
120
CLMP
140
9