LTC3206EUF Linear Technology, LTC3206EUF Datasheet - Page 5
![no-image](/images/manufacturer_photos/0/3/388/linear_technology_sml.jpg)
LTC3206EUF
Manufacturer Part Number
LTC3206EUF
Description
IC LED DRVR WT/RGB BCKLGT 24-QFN
Manufacturer
Linear Technology
Type
Backlight, White LED, RGB (I²C Interface)r
Datasheet
1.LTC3206EUF.pdf
(16 pages)
Specifications of LTC3206EUF
Topology
PWM, Step-Up (Boost), Switched Capacitor (Charge Pump)
Number Of Outputs
11
Internal Driver
Yes
Type - Primary
Backlight
Type - Secondary
RGB, White LED
Frequency
680kHz ~ 1.36MHz
Voltage - Supply
2.7 V ~ 4.5 V
Mounting Type
Surface Mount
Package / Case
24-QFN
Operating Temperature
-40°C ~ 85°C
Current - Output / Channel
400mA
Internal Switch(s)
Yes
Efficiency
92%
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Voltage - Output
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LTC3206EUF
Manufacturer:
LT
Quantity:
10 000
Part Number:
LTC3206EUF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Company:
Part Number:
LTC3206EUF#TRPBF
Manufacturer:
LTC
Quantity:
25 560
PI FU CTIO S
SUB1, SUB2 (Pins 1, 2): Current Source Outputs for the
SUB Display White LEDs. The current for the SUB display
is controlled by the resistor on the I
SUB display can be set to exponentially increasing bright-
ness levels from 0.78% to 100% of full-scale. See Table 1.
C1
Capacitor Pins. A 2.2µF X7R or X5R ceramic capacitor
should be connected from C1
C2
DV
SDA, SCL and ENRGB/S pins.
SDA (Pin 8): Input Data for the I
is shifted in one bit per clock to control the LTC3206 (see
Figures 3 and 4). The logic level for SDA is referenced to
DV
SCL (Pin 9): Clock Input for the I
3 and 4). The logic level for SCL is referenced to DV
ENRGB/S (Pin 10): This pin is used to enable and disable
either the RED, GREEN and BLUE current sources or the
SUB display depending on which is programmed to re-
spond via the I
LTC3206 illuminates the RGB or SUB display with the
color combination or intensity that was previously pro-
grammed via the I
referenced to DV
I
LED current in both the MAIN and SUB LED displays. The
I
The full scale (100%) currents in the MAIN and SUB
display LEDs will be 400 times the current at the I
I
at the RED, GREEN and BLUE LED pins. The I
servos to 0.6V when there is a resistor to ground. The
current in the RED, GREEN and BLUE LEDs will be 400
times the current at the I
scale.
SGND (Pin 13): Ground for the control logic. This pin
should be connected directly to a low impedance ground
plane.
MS
MS
RGB
+
+
U
CC
CC
, C1
pin servos to 0.6V when there is a resistor to ground.
(Pin 11): This pin controls the maximum amount of
to C2
(Pin 12): This pin controls the amount of LED current
.
(Pin 7): This pin sets the logic reference level of the
–
, C2
–
U
.
+
, C2
2
C port. Once ENRGB/S is brought high, the
CC
–
2
C port. The logic level for ENRGB/S is
.
(Pins 5, 4, 6, 3): Charge Pump Flying
U
RGB
pin when programmed to full
+
2
2
to C1
C Serial Port (see Figures
C Serial Port. Serial data
MS
pin.The LEDs on the
–
and another from
RGB
MS
CC
pin.
pin
.
CPO (Pin 14): Output of the Charge Pump. This output
should be used to power white, blue and “true” green
LEDs. Red LEDs can be powered from V
or X7R low impedance (ceramic) 2.2µF charge storage
capacitor is required on CPO.
V
pin should be connected directly to the battery and by-
passed with a 2.2µF X5R or X7R ceramic capacitor.
RED, GREEN, BLUE (Pins 16, 17, 18): Current Source
Outputs for the RGB Illuminator LEDs. The currents for the
RGB LEDs are controlled by the resistor on the I
The RGB LEDs can independently be set to any duty cycle
from 0/15 through 15/15 under software control giving a
total of 16 shades per LED and 4096 colors for the
illuminator. See Table 1. The RGB LEDs are modulated at
1/240 the speed of the charge pump oscillator (approxi-
mately 4kHz).
MAIN1-MAIN4 (Pins 22, 21, 20, 19): Current Source
Outputs for the Main Display White LEDs. The current for
the main display is controlled by the resistor on the I
pin. The LEDs on the MAIN display can be set to 16
exponentially increasing brightness steps from 0.78% to
100% of full scale. See Table 1.
AUX1, AUX2 (Pins 23, 24): Current source outputs for the
auxiliary white LEDs. The auxiliary current sources can be
individually assigned to be either MAIN display or SUB
display LEDs via the I
or AUX2 are assigned to the MAIN display they will have
the same power setting as the other MAIN LEDs. Likewise,
when either AUX1 and/or AUX2 are assigned to the SUB
display they will have the same power setting as the other
SUB LEDs. The currents for the AUX1 and AUX2 pins are
controlled by the resistor on the I
PGND (Pin 25, Exposed Pad): Power Ground for the
Charge Pump. This pin should be connected directly to a
low impedance ground plane.
IN
(Pin 15): Supply Voltage for the Charge Pump. The V
2
C serial port. When either AUX1 and/
MS
pin.
IN
LTC3206
or CPO. An X5R
RGB
pin.
5
3206f
MS
IN