LT3756EUD-2#TRPBF Linear Technology, LT3756EUD-2#TRPBF Datasheet - Page 13
![IC LED DRVR HP CONST CURR 16-QFN](/photos/6/67/66790/161-16-qfn__sml.jpg)
LT3756EUD-2#TRPBF
Manufacturer Part Number
LT3756EUD-2#TRPBF
Description
IC LED DRVR HP CONST CURR 16-QFN
Manufacturer
Linear Technology
Type
High Power, Constant Currentr
Datasheet
1.LT3756EUD-1PBF.pdf
(24 pages)
Specifications of LT3756EUD-2#TRPBF
Constant Current
Yes
Constant Voltage
Yes
Topology
Flyback, Low Side, PWM, SEPIC, Step-Down (Buck), Step-Up (Boost)
Number Of Outputs
1
Internal Driver
No
Type - Primary
Automotive
Type - Secondary
White LED
Frequency
100kHz ~ 1MHz
Voltage - Supply
6 V ~ 100 V
Voltage - Output
100V
Mounting Type
Surface Mount
Package / Case
16-WQFN Exposed Pad
Operating Temperature
-40°C ~ 125°C
Current - Output / Channel
1A
Internal Switch(s)
Yes
Efficiency
94%
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
method uses the PWM pin to modulate the current source
between zero and full current to achieve a precisely pro-
grammed average current. To make PWM dimming more
accurate, the switch demand current is stored on the VC
node during the quiescent phase when PWM is low. This
feature minimizes recovery time when the PWM signal goes
high. To further improve the recovery time, a disconnect
switch may be used in the LED current path to prevent the
ISP node from discharging during the PWM signal low
phase. The minimum PWM on or off time will depend on
the choice of operating frequency and external component
selection. With operation in discontinuous conduction
mode (DCM), regulated current pulses as short as 1µs are
achievable. But, the best overall combination of PWM and
analog dimming (with CTRL) is available if the minimum
PWM pulse is at least six switching cycles.
Programming the Switching Frequency
The RT frequency adjust pin allows the user to program
the switching frequency from 100kHz to 1MHz to optimize
efficiency/performance or external component size. Higher
frequency operation yields smaller component size but
increases switching losses and gate driving current, and
may not allow sufficiently high or low duty cycle operation.
Lower frequency operation gives better performance at the
cost of larger external component size. For an appropriate
R
RT pin to GND is required—do not leave this pin open.
Table 1. Switching Frequency vs R
applicaTions inForMaTion
T
resistor value see Table 1. An external resistor from the
f
OSC
1000
900
800
700
600
500
400
300
200
100
(kHz)
T
Value
R
T
10.0
11.8
13.0
15.4
17.8
21.0
26.7
35.7
53.6
100
(kΩ)
Thermal Considerations
The LT3756 series is rated to a maximum input voltage
of 100V. Careful attention must be paid to the internal
power dissipation of the IC at higher input voltages to
ensure that a junction temperature of 125°C (150°C for
H-grade) is not exceeded. This junction limit is especially
Duty Cycle Considerations
Switching duty cycle is a key variable defining converter
operation, therefore, its limits must be considered when
programming the switching frequency for a particular
application. The fixed minimum on-time and minimum
off-time (see Figure 4) and the switching frequency define
the minimum and maximum duty cycle of the switch,
respectively. The following equations express the mini-
mum/maximum duty cycle:
Min Duty Cycle = (minimum on-time) • switching fre-
quency
Max Duty Cycle = 1 – (minimum off-time) • switching
frequency
When calculating the operating limits, the typical values
for on/off-time in the data sheet should be increased by
at least 60ns to allow margin for PWM control latitude,
GATE rise/fall times and SW node rise/fall times.
LT3756/LT3756-1/LT3756-2
300
250
200
150
100
50
Figure 4. Typical Minimum On and Off
Pulse Width vs Temperature
0
–50
C
GATE
–25
= 3300pF
MINIMUM ON-TIME
MINIMUM OFF-TIME
0
TEMPERATURE (°C)
25
50
75
100
125
375612 F04
150
375612fb