MAX16822AASA+T Maxim Integrated Products, MAX16822AASA+T Datasheet - Page 5
![IC LED DRIVER HIGH BRIGHT 8-SOIC](/photos/1/39/13902/8-soic_21-0042b_sml.jpg)
MAX16822AASA+T
Manufacturer Part Number
MAX16822AASA+T
Description
IC LED DRIVER HIGH BRIGHT 8-SOIC
Manufacturer
Maxim Integrated Products
Type
HBLED Driverr
Datasheet
1.MAX16822AASA.pdf
(10 pages)
Specifications of MAX16822AASA+T
Constant Current
Yes
Topology
PWM, Step-Down (Buck)
Number Of Outputs
1
Internal Driver
Yes
Type - Primary
Automotive
Type - Secondary
High Brightness LED (HBLED)
Frequency
2MHz
Voltage - Supply
6.5 V ~ 65 V
Mounting Type
Surface Mount
Package / Case
8-SOIC (3.9mm Width)
Operating Temperature
-40°C ~ 125°C
Current - Output / Channel
350mA
Internal Switch(s)
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Voltage - Output
-
Efficiency
-
Lead Free Status / Rohs Status
Details
Integrated MOSFET and High-Side Current Sense
The MAX16822A/MAX16822B are step-down, constant-
current, high-brightness LED (HB LED) drivers. These
devices operate from a +6.5V to +65V input-voltage
range. The maximum output current is 500mA, if the
part is used at temperatures up to +105°C, or 350mA, if
it is used up to +125°C. A high-side current-sense
resistor sets the output current and a dedicated PWM
(V
unless otherwise noted.)
IN
= V
PIN
5, 6
1
2
3
4
7
8
DIM
= 48V, C
1.0
0.9
0.8
0.7
0.6
0.5
0.4
-40
TEMP_I
-25
NAME
_______________________________________________________________________________________
PGND
VCC
GND
DIM
CS
LX
IN
-10
2MHz, High-Brightness LED Drivers with
Detailed Description
= 1µF, R
vs. TEMPERATURE
5
V
TEMPERATURE (°C)
IN
20
= 48V
LX
35
RDSON
Current-Sense Input. Connect a resistor between IN and CS to program the LED current.
Positive Supply Voltage Input. Bypass with a 1μF or higher value capacitor to GND.
Ground
Power Ground
Switching Node
Logic-Level Dimming Input. Drive DIM low to turn off the current regulator. Drive DIM high to
enable the current regulator.
Thermal Foldback Control and Linear Input. Bypass with a 0.01μF capacitor to GND if thermal
foldback or analog dimming is used. See the Thermal Foldback section for more details.
SENSE
50
V
IN
65
= 65V
= 0.62Ω, L = 220µH (connected between IN and CS). Typical values are at T
V
80
IN
= 6.5V
95
110
Typical Operating Characteristics (continued)
125
dimming input enables pulsed LED dimming over a
wide range of brightness levels.
A high-side current-sensing scheme and an on-board
current-setting circuitry minimize the number of exter-
nal components while delivering LED current with ±3%
accuracy, using a 1% sense resistor. See Figure 1 for
an internal block diagram.
FUNCTION
30.0
29.5
29.0
28.5
28.0
27.5
27.0
26.5
26.0
25.5
25.0
-40
V
-25
IN
= 48V
-10
vs. TEMPERATURE
5
TEMPERATURE (°C)
20
I
TEMP_I
35
50
65
Pin Description
80
95
110
125
A
= +25°C,
5