MAX1576ETG+ Maxim Integrated Products, MAX1576ETG+ Datasheet
MAX1576ETG+
Specifications of MAX1576ETG+
Related parts for MAX1576ETG+
MAX1576ETG+ Summary of contents
Page 1
... Supply Voltage Range ♦ Soft-Start Limits Inrush Current ♦ Output Overvoltage Protection ♦ Thermal-Shutdown Protection ♦ 24-Pin Thin QFN, 4mm x 4mm Package Applications PART MAX1576ETG MAX1576ETG+ + Denotes lead-free package. Pin Configuration appears at end of data sheet. 1μF 1μF OUTPUT UP TO 480mA C1P ...
Page 2
White LED 1x/1.5x/2x Charge Pump for Backlighting and Camera Flash ABSOLUTE MAXIMUM RATINGS INP, IN, OUT, ENM1, ENM2, ENF1, ENF2 to GND1 .......................................................-0.3V to +6.0V SETF, SETM, LED1, LED2, LED3, LED4, LED5, LED6, LED7, LED8 to GND1 ....................-0.3V to ...
Page 3
White LED 1x/1.5x/2x Charge Pump for ELECTRICAL CHARACTERISTICS (continued 3.6V GND1 GND2 PGND unless otherwise noted. Typical values are at T PARAMETER LED_ Leakage in Shutdown ENM1 = ENM2 = ENF1 ...
Page 4
White LED 1x/1.5x/2x Charge Pump for Backlighting and Camera Flash (V = 3.6V, EN_ = IN, Circuit of Figure EFFICIENCY vs. Li+ BATTERY VOLTAGE DRIVING FOUR MAIN LEDs 100 90 15mA/LED 80 4.5mA/LED 70 1.5mA/LED 60 ...
Page 5
White LED 1x/1.5x/2x Charge Pump for (V = 3.6V, EN_ = IN, Circuit of Figure LED CURRENT vs. R 100 10 100% BRIGHTNESS SETTING SETM OPERATING WAVEFORMS (1x MODE) V OUT V ...
Page 6
White LED 1x/1.5x/2x Charge Pump for Backlighting and Camera Flash (V = 3.6V, EN_ = IN, Circuit of Figure SINGLE-WIRE DIMMING RESPONSE V , EN1M V EN2M I OUT V OUT 2ms/div PIN NAME Output. Bypass ...
Page 7
... When the input voltage rises above two- thirds V by approximately 50mV, the MAX1576 OUT switches back to 1.5x mode. True Shutdown is a trademark of Maxim Integrated Products, Inc. _______________________________________________________________________________________ Backlighting and Camera Flash Pin Description (continued) FUNCTION The MAX1576 includes soft-start circuitry to limit inrush current at turn-on ...
Page 8
White LED 1x/1.5x/2x Charge Pump for Backlighting and Camera Flash INPUT 2.7V TO 5.5V INP 4.7μF C2 1μF PGND CONTROL AND ENM1 REFERENCE ENM2 0.15V ENF1 FLASH CONTROL ENF2 MAIN CONTROL 0.604V IN ERROR AMP 2 ...
Page 9
White LED 1x/1.5x/2x Charge Pump for 1μF 1μF INPUT C1P C1N C2P C2N 2.7V TO 5.5V INP OUT IN 4.7μF 1μF PGND MAX1576 LED1 GND1 LED2 LED3 LED4 ENM1 LED5 ENM2 ON/OFF AND LED6 CURRENT SETTING ENF1 LED7 ENF2 ...
Page 10
White LED 1x/1.5x/2x Charge Pump for Backlighting and Camera Flash INPUT 2.7V TO 5.5V 4.7μF 1μF ON OFF PWM INPUT ON/OFF AND CURRENT SETTING Figure 4. Dimming Using PWM Signal into ENM1 INPUT 2.7V TO 5.5V 4.7μF 1μF ON/OFF ...
Page 11
White LED 1x/1.5x/2x Charge Pump for INPUT 2.7V TO 5.5V 4.7μF 1μF ON/OFF AND CURRENT SETTING Figure 6. Providing Increased LED Current per LED INPUT 2.7V TO 5.5V 4.7μF 1μF ON/OFF AND CURRENT SETTING Figure 7. Schematic for when ...
Page 12
White LED 1x/1.5x/2x Charge Pump for Backlighting and Camera Flash Table 3. Recommended Components DESIGNATION VALUE MANUFACTURER 4.7µF IN OUT C2, C3, C4 1µF D1–D4 — D5 (D5–D8) — required SETM SETF ...
Page 13
White LED 1x/1.5x/2x Charge Pump for (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information go to www.maxim-ic.com/packages.) ______________________________________________________________________________________ Backlighting and Camera Flash Package Information PACKAGE OUTLINE, 12, ...
Page 14
... Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 14 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 © 2005 Maxim Integrated Products Package Information (continued) Printed USA is a registered trademark of Maxim Integrated Products, Inc ...