DS3992Z-09P+ Maxim Integrated Products, DS3992Z-09P+ Datasheet - Page 5
![IC CTRLR CCFL 90-220HZ 16-SOIC](/photos/6/66/66630/175-16-soic_sml.jpg)
DS3992Z-09P+
Manufacturer Part Number
DS3992Z-09P+
Description
IC CTRLR CCFL 90-220HZ 16-SOIC
Manufacturer
Maxim Integrated Products
Type
CCFL Controllerr
Datasheet
1.DS3992Z-18P.pdf
(13 pages)
Specifications of DS3992Z-09P+
Frequency
40 ~ 80 kHz
Current - Supply
8mA
Voltage - Supply
4.5 V ~ 5.5 V
Operating Temperature
-40°C ~ 85°C
Package / Case
16-SOIC (3.9mm Width)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Current - Output
-
Lead Free Status / Rohs Status
Details
NUMBER
PIN
10
11
12
13
14
15
16
1
2
3
4
5
6
7
8
9
BRIGHT
NAME
POSC
LOSC
LCM1
OVD1
LCM2
OVD2
GND
SVM
GA1
GB1
GA2
GB2
V
V
V
CC
CC
CC
Two-Channel, Push-Pull CCFL Controller
I/O
⎯
⎯
⎯
⎯
⎯
⎯
O
O
O
O
I
I
I
I
I
I
Lamp Oscillator Resistor Adjust. A resistor (R
the lamp oscillator (f
Burst Dimming DPWM Oscillator Resistor Adjust. A resistor (RPOSC) to ground on this lead
sets the frequency (f
for DS3992Z-09P and DS3992Z-09N and R
DS3992Z-18N].
Lamp Brightness Control. An analog voltage at this input controls the lamp brightness. See
Table 1 for details.
Supply Voltage Monitor. The DC inverter supply voltage is monitored by an external resistor
divider. The resistor-divider should be set such that it provides 2V at this pin for the minimum
allowable range of the DC inverter supply. Pulling this input below 2V will turn the lamps off and
reset the controller. Connect to V
MOSFET Gate Drive A for Channel 1. Connect directly to the gate of a logic-level mode
n-channel MOSFET.
MOSFET Gate Drive B for Channel 1. Connect directly to the gate of a logic-level mode
n-channel MOSFET.
Lamp Current Monitor Input for Channel 1. Lamp current is monitored by a resistor placed in
series with the low-voltage side of the lamp.
Over Voltage Detection for Channel 1. Lamp voltage is monitored by a capacitor divider
placed on the high-voltage side of the lamp.
Signal Ground
Supply. 4.5V to 5.5V.
MOSFET Gate Drive A for Channel 2. Connect directly to the gate of a logic-level mode
n-channel MOSFET.
MOSFET Gate Drive B for Channel 2. Connect directly to the gate of a logic-level mode
n-channel MOSFET.
Lamp Current Monitor Input for Channel 2. Lamp current is monitored by a resistor placed in
series with the low-voltage side of the lamp.
Overvoltage Detection for Channel 2. Lamp voltage is monitored by a capacitor divider
placed on the high-voltage side of the lamp.
Supply. 4.5V to 5.5V.
Supply. 4.5V to 5.5V.
_____________________________________________________________________
LFS:OSC
DSR:OSC
). [R
) of the burst-dimming DPWM oscillator. [R
LOSC
CC
if not used.
x f
LFS:OSC
POSC
FUNCTION
LOSC
x f
= 1.6E9].
DSR:OSC
) to ground on this pin sets the frequency of
= 8.0E6 for DS3992Z-18P and
Pin Description
POSC
x f
DSR:OSC
= 4.0E6
5