MIC5016YWM Micrel Inc, MIC5016YWM Datasheet - Page 8
![no-image](/images/manufacturer_photos/0/4/434/micrel_inc_sml.jpg)
MIC5016YWM
Manufacturer Part Number
MIC5016YWM
Description
IC DRIVER MOSF DUAL HI/LO 16SOIC
Manufacturer
Micrel Inc
Datasheet
1.MIC5016BN.pdf
(12 pages)
Specifications of MIC5016YWM
Configuration
High and Low Side, Independent
Input Type
Non-Inverting
Delay Time
2.5ms
Number Of Configurations
1
Number Of Outputs
2
Voltage - Supply
2.75 V ~ 30 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
16-SOIC (0.300", 7.5mm Width)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Current - Peak
-
High Side Voltage - Max (bootstrap)
-
Other names
576-1237
MIC5016/5017
MIC5016/5017
nation of an MIC5016/5017 and a power FET makes an
effective driver for a standard incandescent or halogen lamp
load. Such loads often have high inrush currents, as the
resistance of a cold filament is less than one-tenth as much as
when it is hot. Power MOSFETs are well suited to this
application as they have wider safe operating areas than do
power bipolar transistors. It is important to check the SOA
curve on the data sheet of the power FET to be used against
the estimated or measured inrush current of the lamp in
question prior to prototyping to prevent “explosive” results.
If overcurrent sense is to be used, first measure the duration
of the inrush, then use the topology of Figure 5 with the RC of
the timer chosen to accomodate the duration with suitable
guardbanding.
Relay Driver (Figure 9) Some power relay applications re-
quire the use of a separate switch or drive control, such as in
the case of microprocessor control of banks of relays where
a logic level control signal is used, or for drive of relays with
high power requirements. The combination of an MIC5016/
5017 and a power FET also provides an elegant solution to
power relay drive.
Incandescent/Halogen Lamp Driver (Figure 8) The combi-
OFF
ON
Control Input
10µF
OFF
ON
Control Input
10µF
Figure 9: Relay Driver
Figure 8: Halogen Lamp Driver
Source
V+
Input
Gnd
1/2 MIC5016
V+
Input
Source
Gnd
1/2 MIC5016
Gate
Gate
HLX64623
OSRAM
12V
IRF540
Guardian Electric
12V
1725-1C-12D
IRF540
8
Motor Driver With Stall Shutdown (Figure 10) Tachometer
feedback can be used to shut down a motor driver circuit when
a stall condition occurs. The control switch is a 3-way type; the
“START” position is momentary and forces the driver ON.
When released, the switch returns to the “RUN” position, and
the tachometer’s output is used to hold the MIC5016 input ON.
If the motor slows down, the tach output is reduced, and the
MIC5016 switches OFF. Resistor “R” sets the shutdown
threshold.
Simple DC-DC Converter (Figure 11) The simplest applica-
tion for the MIC5016 is as a basic one-chip DC-DC converter.
As the output (Gate) pin has a relatively high impedance, the
output voltage shown will vary significantly with applied load.
10µF
R
330k
Figure 10. Motor Stall Shutdown
1N4148
Figure 11. DC - DC Converter
330k
5V
Input
Source
Gnd
V+
1/2 MIC5016
V+
Input
Source
Gnd
1/2 MIC5016
Gate
T
Gate
10µF
V
OUT
= 12V
12V
M
IRFZ44
October 1998
Micrel