VN920SO-E STMicroelectronics, VN920SO-E Datasheet
VN920SO-E
Specifications of VN920SO-E
Related parts for VN920SO-E
VN920SO-E Summary of contents
Page 1
... PENTAWATT Description The VN920 monolithic device designed in STMicroelectronics VIPower™ M0-3 technology, intended for driving any kind of load with one side connected to ground. Active V clamp protects the device against low energy spikes (see ISO7637 transient compatibility able). Active current limitation combined with thermal ...
Page 2
Contents Contents 1 Block diagram and pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2 Electrical ...
Page 3
VN920-E List of tables Table 1. Device summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 4
List of figures List of figures Figure 1. Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 5
VN920-E 1 Block diagram and pin description Figure 1. Block diagram GND INPUT Figure 2. Configuration diagram (top view) Table 2. Suggested connections for unused and not connected pins Connection / pin Floating To ground OVERVOLTAGE V CC DETECTION CLAMP ...
Page 6
... These are stress ratings only and operation of the device at these or any other conditions above those indicated in the operating sections of this specification is not implied. Exposure to Absolute maximum rating conditions for extended periods may affect device reliability. Refer also to the STMicroelectronics sure program and other relevant quality document. Table 3. ...
Page 7
VN920-E Table 3. Absolute maximum ratings (continued) Symbol E MAX P tot stg 2.2 Thermal data Table 4. Thermal data Symbol R Thermal resistance junction-case (max) thj-case R Thermal resistance junction-lead (max) thj-lead R Thermal ...
Page 8
Electrical specifications Table 5. Power (continued) Symbol Parameter I Off-state output current L(off2) I Off-state output current L(off3) I Off-state output current L(off4 and V are correlated. Typical difference is 5V. clamp OV Table 6. Switching (V Symbol ...
Page 9
VN920-E Table 9. Protections Symbol Parameter Turn-off output clamp V demag voltage Output voltage drop V ON limitation 1. To ensure long term reliability under heavy over-load or short circuit conditions, protection and related diagnostic signals must be used together ...
Page 10
Electrical specifications Figure 4. I OUT I /I OUT SENSE 6500 6000 5500 5000 4500 4000 3500 3000 0 2 Figure 5. Switching characteristics V OUT dV I SENSE INPUT 10/23 /I versus I SENSE OUT max.Tj=25...150°C min.Tj=25...150° ...
Page 11
VN920-E Table 11. Truth table Conditions Normal operation Over temperature Undervoltage Overvoltage Short circuit to GND Short circuit Negative output voltage clamp Table 12. Electrical transient requirements (part 1/3) ISO T/R 7637/1 Test pulse ...
Page 12
Electrical specifications Table 14. Electrical transient requirements (part 3/3) Class C All functions of the device are performed as designed after exposure to disturbance. One or more functions of the device are not performed as designed after exposure to E ...
Page 13
VN920-E Figure 6. Waveforms INPUT LOAD CURRENT SENSE V CC INPUT LOAD CURRENT SENSE V CC INPUT LOAD CURRENT SENSE INPUT LOAD CURRENT LOAD VOLTAGE SENSE INPUT LOAD VOLTAGE LOAD CURRENT SENSE T j INPUT LOAD CURRENT SENSE NORMAL OPERATION ...
Page 14
Electrical specifications 2.4 Electrical characteristics curves k Figure 7. Off-state output current Figure 9. Input clamp voltage Figure 11. On-state resistance vs T 14/23 Figure 8. High level input current Figure 10. On-state resistance vs V Figure 12. Input high ...
Page 15
VN920-E Figure 13. Input low level voltage Figure 15. Turn-on voltage slope Figure 17. Overvoltage shutdown Figure 14. Input hysteresis voltage Figure 16. Turn-off voltage slope Figure 18. I LIM Doc ID 10894 Rev 3 Electrical specifications vs T case ...
Page 16
Application information 3 Application information Figure 19. Application schematic + μC 3.1 GND protection network against reverse battery 3.1.1 Solution 1: resistor in the ground line (R This can be used with any type of load. The following ...
Page 17
VN920-E 3.1.2 Solution 2: diode (D A resistor (R GND inductive load. This small signal diode can be safely shared amongst several different HSDs. Also in this case, the presence of the ground network will produce a shift (≈600mV) in ...
Page 18
Package and packing information 4 Package and packing information ® 4.1 ECOPACK In order to meet environmental requirements, ST offers these devices in different grades of ® ECOPACK packages, depending on their level of environmental compliance. ECOPACK specifications, grade definitions ...
Page 19
VN920-E Table 15. PENTAWATT (vertical) mechanical data (continued) Symbol Diam. Package and packing information millimeters Min Typ 1 3.2 3.4 6.6 6.8 10.05 17.85 15.75 21.4 ...
Page 20
Package and packing information 4.1.2 PENTAWATT (in-line) mechanical data PENTAWATT (in-line) package dimensions Figure 21. Table 16. PENTAWATT (in-line) mechanical data Symbol 20/23 millimeters Min Typ ...
Page 21
VN920-E Table 16. PENTAWATT (in-line) mechanical data (continued) Symbol Diam. 4.2 PENTAWATT packing information Figure 22. PENTAWATT tube shipment (no suffix) B Package and packing information millimeters Min Typ 0.9 2.6 15.1 6 90° 3.65 ...
Page 22
... Revision history Table 17. Document revision history Date 22-Oct-2004 22-Sep-2009 08-Oct-2009 22/23 Revision 1 Initial release. 2 Removed all the references to VN920B5-E and VN920SO-E Added PENTAWATT in-line package: 3 – UpdatedTable 1: Device – Added Section 4.1.2: PENTAWATT (in-line) mechanical Doc ID 10894 Rev 3 Changes summary. data. VN920-E ...
Page 23
... VN920-E Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. ...