MIC2546-1BM TR Micrel Inc, MIC2546-1BM TR Datasheet
MIC2546-1BM TR
Specifications of MIC2546-1BM TR
MIC2546-1BMTR
Related parts for MIC2546-1BM TR
MIC2546-1BM TR Summary of contents
Page 1
... The enable signal is compatible with both 3V and 5V logic, and is also used as the thermal shutdown latch reset for the MIC2547. The MIC2546 and MIC2547 are available in active-high and active-low enable versions in 16-pin TSSOP and SOP packages. Data sheets and support documentation can be found on Micrel’ ...
Page 2
... Micrel, Inc. Ordering Information Part Number Standard Pb-Free MIC2546-1BM MIC2546-1YM MIC2546-1BTS MIC2546-1YTS MIC2546-2BM MIC2546-2YM MIC2546-2BTS MIC2546-2YTS MIC2547-1BM MIC2547-1YM MIC2547-1BTS MIC2547-1YTS MIC2547-2BM MIC2547-2YM MIC2547-2BTS MIC2547-2YTS Note: 1. Thermal Shutdown Latch. Pin Configuration 16-Pin SOP (M) 16-Pin TSSOP (TS) January 2008 (1) Enable Latch Junction Temp. Range ...
Page 3
... Ground. Both pins must be connected to GND. Current Limit Channel B: Sets current-limit threshold using an resistor, R connected to ground. 154Ω < R < 2.29kΩ. SET Switch B (Output): Pins 8 and 11 must be externally connected. Input B Enable B (Input) Fault Flag B (Output) Fault Flag B (Output) 3 MIC2546/2547 , SET M9999-012508-A ...
Page 4
... Note 3. Devices are ESD sensitive. Handling precautions recommended. Human body model, 1.5k in series with 100pF. Note 4. Off is ″ 0.8V and on is ≥ 2.4V for the MIC2546-1 and MIC2547-1. Off is ≥ 2.4V and on is ″ 0.8V for the MIC2546-2 and MIC2547-2. The enable input has about 200mV of hysteresis ...
Page 5
... Micrel, Inc. Note 5. Guaranteed by design, but not production tested. Note 6. Current limit threshold is determined by: January 2008 230V = I LIMIT R , where ohms. SET SET 5 MIC2546/2547 M9999-012508-A ...
Page 6
... Micrel, Inc. Typical Characteristics January 2008 6 MIC2546/2547 M9999-012508-A ...
Page 7
... Micrel, Inc. January 2008 7 MIC2546/2547 M9999-012508-A ...
Page 8
... Micrel, Inc. Functional Characteristics January 2008 8 MIC2546/2547 M9999-012508-A ...
Page 9
... Micrel, Inc. Test Circuit Timing Diagrams January 2008 Functional Characteristics Test Circuit Figure 1a. MIC2546/47-1 Figure 1b. MIC2546/47-2 9 MIC2546/2547 M9999-012508-A ...
Page 10
... Micrel, Inc. Figure 2a. MIC2547-2 Timing: Output is reset by toggling EN January 2008 Figure 2b. MIC2546-2 Timing 10 MIC2546/2547 M9999-012508-A ...
Page 11
... Micrel, Inc. Block Diagram January 2008 11 MIC2546/2547 M9999-012508-A ...
Page 12
... Micrel, Inc. Functional Description The MIC2546 and MIC2547 are dual high-side N- channel switches available with active-high or active-low enable inputs. Fault conditions turn off or inhibit turn-on of the output transistor and activate the open-drain error flag transistor making it sink current to ground. Input and Output INX is the power supply connection to the logic circuitry and the drain of the output MOSFET ...
Page 13
... USB Power Distribution The MIC2546 is ideal for meeting USB power distribution requirements. Figure 3 depicts a USB Host application. RSET should be set to a value providing a current-limit >500mA. The accurate current-limit of the MIC2546 will reduce power supply current requirements ...
Page 14
... Micrel, Inc. January 2008 Figure 3. USB Host Application 14 MIC2546/2547 M9999-012508-A ...
Page 15
... Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to fully January 2008 16-Pin SOP (M) 16-Pin TSSOP (TS) indemnify Micrel for any damages resulting from such use or sale. © 2001 Micrel, Incorporated. 15 MIC2546/2547 M9999-012508-A ...