TC649EUATR Microchip Technology, TC649EUATR Datasheet - Page 5
![IC PWM FAN SPD CONTRLR SD 8-MSOP](/photos/6/59/65932/mfg_150_c04-111_ms_8-msop_sml.jpg)
TC649EUATR
Manufacturer Part Number
TC649EUATR
Description
IC PWM FAN SPD CONTRLR SD 8-MSOP
Manufacturer
Microchip Technology
Type
Controller - PWM Fanr
Specifications of TC649EUATR
Applications
Fan Controller, Brushless (BLDC)
Number Of Outputs
1
Voltage - Supply
3 V ~ 5.5 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
8-MSOP, Micro8™, 8-uMAX, 8-uSOP,
Product
Fan / Motor Controllers / Drivers
Operating Supply Voltage
3 V to 5.5 V
Supply Current
400 uA
Mounting Style
SMD/SMT
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Current - Output
-
Voltage - Load
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
3.0
3.1
The PWM circuit consists of a ramp generator and
threshold detector. The frequency of the PWM is
determined by the value of the capacitor connected to
the C
most applications (C
time base for the Start-up Timer (see Section 3.3,
“Start-up Timer”). The PWM voltage control range is
1.25V to 2.65V (typical) for 0% to 100% output duty
cycle.
3.2
The V
or MOSFET as the low side power switching element in
the system. Various examples of driver circuits will be
shown throughout the datasheet. This output has
asymmetric complementary drive and is optimized for
driving NPN transistors or N-channel MOSFETs. Since
the system relies on PWM rather than linear control,
the power dissipation in the power switch is kept to a
minimum. Generally, very small devices (TO-92 or SOT
packages) will suffice.
3.3
To ensure reliable fan start-up, the Start-up Timer turns
the V
the fan is started from the off state. This occurs at
power-up and when coming out of shutdown or auto-
shutdown mode. If the PWM frequency is 30 Hz (C
1 µF) the resulting start-up time will be approximately
one second. If a fan fault is detected (see Section 3.5,
FAULT Output), the Diagnostic Timer is triggered once,
followed by the Start-up Timer. If the fault persists, the
device is shut down (see Section 3.5, FAULT Output).
3.4
The SENSE input (Pin 5) is connected to a low value
current sensing resistor in the ground return leg of the
fan circuit. During normal fan operation, commutation
occurs as each pole of the fan is energized. This
causes brief interruptions in the fan current, seen as
pulses across the sense resistor. If the device is not in
shutdown or auto-shutdown mode, and pulses are not
appearing at the SENSE input, a fault exists.
The short, rapid change in fan current (high dl/dt)
causes a corresponding dV/dt across the sense
resistor, R
differentiated and converted to a logic-level pulse-train
by C
The presence and frequency of this pulse-train is a
direct indication of fan operation. See Section 5.0,
“Typical Applications”, for more details.
2002 Microchip Technology Inc.
SENSE
OUT
F
OUT
input. A frequency of 30 Hz is recommended for
Start-Up Timer
SENSE Input
DETAILED DESCRIPTION
PWM
V
(FanSense™ Technology)
output on for 32 cycles of the PWM whenever
pin is designed to drive a low cost transistor
OUT
and the internal signal processing circuitry.
SENSE
Output
. The waveform on R
F
= 1 µF). The PWM is also the
SENSE
F
is
=
3.5
Pulses appearing at SENSE due to the PWM turning
on are blanked, and the remaining pulses are filtered
by a missing pulse detector. If consecutive pulses are
not detected for thirty-two PWM cycles ( 1 Sec if
C
V
( 100 msec if C
within this window, the Start-up Timer is triggered (see
Section 3.3, “Start-up Timer”). This should clear a tran-
sient fault condition. If the missing pulse detector times
out again, the PWM is stopped and FAULT goes low.
When FAULT is activated due to this condition, the
device is latched in shutdown mode and will remain off
indefinitely. The TC649 is thus prevented from
attempting to drive a fan under catastrophic fault
conditions.
One of two things will restore operation: Cycling power
off and then on again; or pulling V
releasing it to a level above V
two conditions is satisfied, the normal start-up cycle is
triggered and operation will resume, provided the fault
has been cleared.
3.6
If the voltage on V
V
mode). The TC649 exits auto-shutdown mode when
the voltage on V
V
see Figure 3-1). The Start-up Timer is triggered and
normal operation is resumed upon exiting auto-shut-
down mode. The FAULT output is unconditionally
inactive in auto-shutdown mode.
AS
AS
OUT
F
= 1 µF), the Diagnostic Timer is activated, and
, the fan is automatically shut off (auto-shutdown
by V
is driven high continuously for three PWM cycles
FAULT Output
Auto-Shutdown Mode
HAS
(the auto-shutdown hysteresis voltage,
IN
F
IN
becomes higher than the voltage on
= 1 µF). If a pulse is not detected
becomes less than the voltage on
REL
. When one of these
IN
below V
DS21449C-page 5
TC649
SHDN
and