LTC4414IMS8#TRPBF Linear Technology, LTC4414IMS8#TRPBF Datasheet - Page 6
![IC CNTRLR POWERPATH 8-MSOP](/photos/6/57/65743/8-msop_05-08-1660_sml.jpg)
LTC4414IMS8#TRPBF
Manufacturer Part Number
LTC4414IMS8#TRPBF
Description
IC CNTRLR POWERPATH 8-MSOP
Manufacturer
Linear Technology
Series
PowerPath™r
Datasheet
1.LTC4414EMS8PBF.pdf
(12 pages)
Specifications of LTC4414IMS8#TRPBF
Applications
Battery Backup, Industrial/Automotive, High Current Switch
Fet Type
P-Channel
Number Of Outputs
1
Internal Switch(s)
No
Delay Time - On
600µs
Delay Time - Off
20µs
Voltage - Supply
3 V ~ 36 V
Current - Supply
33µA
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
8-MSOP, Micro8™, 8-uMAX, 8-uSOP,
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
LTC4414
OPERATIO
6
Operation can best be understood by referring to the Block
Diagram, which illustrates the internal circuit blocks along
with the few external components, and the graph that
accompanies the Typical Application drawing on the front
page of the data sheet. The terms primary and auxiliary are
arbitrary and may be changed to suit the application.
Operation begins when either or both power sources are
applied and the CTL control pin is below the input low
voltage of 0.35V (V
present, the Power Source Selector will power the LTC4414
from the V
Analog Controller block that is proportional to the voltage
difference in the V
SENSE is lower than V
Controller will instruct the Linear Gate Driver and Voltage
Clamp block to pull down the GATE pin voltage and turn on
the external P-channel MOSFET. The dynamic pull-down
current of 300µA (I
reaches ground or the gate clamp voltage. The gate clamp
voltage is 8.5V (V
As the SENSE voltage pulls up to V
will regulate the GATE voltage to maintain a 20mV differ-
ence between V
MOSFET. The system is now in the forward regulation
mode and the load will be powered from the primary
supply. As the load current varies, the GATE voltage will be
controlled to maintain the 20mV difference. If the load
current exceeds the P-channel MOSFET’s ability to deliver
the current with a 20mV V
the MOSFET will behave as a fixed resistor and the forward
voltage will increase slightly. While the MOSFET is on the
STAT pin is an open circuit.
When an auxiliary supply is applied, the SENSE pin will be
pulled higher than the V
IN
pin. Amplifier A1 will deliver a current to the
IN
G(ON)
U
IN
and V
G(SNK)
and SENSE pins. While the voltage on
IL
) below the higher of V
). If only the primary supply is
SENSE
IN
IN
) stops when the GATE voltage
DS
pin through the external diode.
– 20mV (V
the GATE voltage will clamp,
which is also the V
IN
– 20mV, the LTC4414
FR
), the Analog
IN
or V
DS
SENSE
of the
.
The Power Source Selector will power the LTC4414
from the SENSE pin. As the SENSE voltage pulls above
V
Gate Driver and Voltage Clamp block to pull the GATE
voltage up to turn off the P-channel MOSFET. When the
voltage on SENSE is higher than V
Analog Controller will instruct the Linear Gate Driver and
Voltage Clamp block to rapidly pull the GATE pin voltage
to the SENSE pin voltage. This action will quickly finish
turning off the external P-channel MOSFET if it hasn’t
already turned completely off. For a clean transition, the
reverse turn-off threshold has hysteresis to prevent
uncertainty. The system is now in the reverse turn-off
mode. Power to the load is being delivered through the
external diode and no current is drawn from the primary
supply. The external diode provides protection in case
the auxiliary supply is below the primary supply, sinks
current to ground or is connected reverse polarity.
During the reverse turn-off mode of operation the STAT
pin will sink a current (I
external MOSFET is wired so that the drain to source
diode will momentarily forward bias when power is first
applied to V
auxiliary supply is applied.
When the CTL (control) input is asserted high, the external
MOSFET will have its gate to source voltage forced to a
small voltage V
mum of 50µA of current if connected. This feature is useful
to allow control input switching of the load between two
power sources as shown in Figure 3 or as a switchable
high side driver as shown in Figure 7. A 3.5µA internal pull-
down current (I
input if the pin should become open.
IN
– 20mV, the Analog Controller will instruct the Linear
IN
and will become reverse biased when an
G(OFF)
CTL
) on the CTL pin will insure a low level
and the STAT pin will sink a mini-
S(SNK)
) if connected. Note that the
IN
+ 20mV (V
RTO
), the
4414fc