AD637ARZ Analog Devices Inc, AD637ARZ Datasheet - Page 14

• Manufacturer Part Number: AD637ARZ
• Description: IC RMS/DC CONV PRECISION 16-SOIC
• Manufacturer: Analog Devices Inc

Specifications of AD637ARZ

• Current - Supply: 2.2mA
• Voltage - Supply: ±3.0V ~ 18V
• Mounting Type: Surface Mount
• Package / Case: 16-SOIC (0.300", 7.5mm Width)
• Accuracy %: 0.25%
• Bandwidth: 200kHz
• Supply Current: 2.2mA
• Power Dissipation Pd: 108mW
• Supply Voltage Range: ± 3V To ± 18V
• Digital Ic Case Style: SOIC
• No. Of Pins: 16
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AD637-EVALZ - BOARD EVALUATION FOR AD637
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

LOW FREQUENCY MEASUREMENTS
If the frequencies of the signals to be measured are below 10 Hz,
the value of the averaging capacitor required to deliver even 1%
averaging error in the standard rms connection becomes
extremely large. Figure 21 shows an alternative method of
obtaining low frequency rms measurements. The averaging
time constant is determined by the product of R and C
this circuit, 0.5 sec/μF of C
reduction in the value of the averaging capacitor, permitting the
use of high quality tantalum capacitors. It is suggested that the
2-pole, Sallen-Key filter shown in Figure 21 be used to obtain a
low ripple level and minimize the value of the averaging
capacitor.
If the frequency of interest is below 1 Hz, or if the value of the
averaging capacitor is still too large, the 20:1 ratio can be
increased. This is accomplished by increasing the value of R.
If this is done, it is suggested that a low input current, low offset
voltage amplifier, such as the AD548, be used instead of the
internal buffer amplifier. This is necessary to minimize the
offset error introduced by the combination of amplifier input
currents and the larger resistance.
AD637
OUTPUT
ADJUST
OFFSET
NOTES
1. VALUES CHOSEN TO GIVE 0.1% AVERAGING ERROR @ 1Hz.
2. NC = NO CONNECT.
50kΩ
+V
–V
S
S
1MΩ
AV
. This circuit permits a 20:1
+V
4.7kΩ
S
1
2
3
4
5
6
7
BUFF IN
COMMON
OUTPUT
OFFSET
DEN
INPUT
dB OUTPUT
NC
CS
25kΩ
Figure 21. AD637 as a Low Frequency RMS Converter
SECTION
BIAS
BUFFER
AV1
C
3.3µF
AV1
, in
SQUARER/DIVIDER
499kΩ 1%
Rev. K | Page 14 of 20
AD637
ABSOLUTE
R
VALUE
FILTER
25kΩ
BUFF
VECTOR SUMMATION
Vector summation can be accomplished through the use of two
AD637s, as shown in Figure 22. Here, the averaging capacitors
are omitted (nominal 100 pF capacitors are used to ensure
stability of the filter amplifier), and the outputs are summed as
shown. The output of the circuit is
This concept can be expanded to include additional terms by
feeding the signal from Pin 9 of each additional AD637 through
a 10 kΩ resistor to the summing junction of the AD711 and
tying all of the denominator inputs (Pin 6) together.
If C
If the averaging capacitor is included on both IC1 and IC2, the
output is
This circuit has a dynamic range of 10 V to 10 mV and is
limited only by the 0.5 mV offset voltage of the AD637.
The useful bandwidth is 100 kHz.
OUT
C
+V
–V
V
NC
AV
IN
S
S
AV
V
14
13
12
11
10
9
8
+
is added to IC1 in this configuration, then the output is
OUT
V
V
3.3MΩ
X
V
X
100µF
+V
–V
OUT
2
2
=
+
S
+
S
SIGNAL
INPUT
V
V
V
Y
3.3MΩ
Y
2
X
2
1µF
2
+
V RMS
1µF
V
V
IN
Y
2
2
3
2
6.8MΩ
AD548JN
1000pF
V+
V–
4
7
6
V RMS OUTPUT
FILTERED