EMC1402-1-ACZL-TR SMSC, EMC1402-1-ACZL-TR Datasheet - Page 26

• Manufacturer Part Number: EMC1402-1-ACZL-TR
• Description: IC TEMP SNSR DUAL 3.3V 8MSOP
• Manufacturer: SMSC

Specifications of EMC1402-1-ACZL-TR

• Function: Temp Monitoring System (Sensor)
• Topology: ADC (Sigma Delta), Comparator, Multiplexer, Register Bank
• Sensor Type: External & Internal
• Sensing Temperature: -40°C ~ 125°C, External Sensor
• Output Type: SMBus™
• Output Alarm: No
• Output Fan: Yes
• Voltage - Supply: 3 V ~ 3.6 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 8-MSOP, Micro8™, 8-uMAX, 8-uSOP,
• For Use With: EVB-EMC1402 - EVAL BOARD FOR EMC1402
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 638-1067-2

ADDR
03h
09h
Revision 1.36 (07-02-09)
6.4
R/W
R/W
Configuration
REGISTER
The status bits (except E1THERM and ITHERM) will remain set until read unless the ALERT pin is
configured as a second THERM output (see
Bit 7 - BUSY - This bit indicates that the ADC is currently converting. This bit does not cause either
the ALERT or THERM pins to be asserted.
Bit 6 - IHIGH - This bit is set when the Internal Diode channel exceeds its programmed high limit.
When set, this bit will assert the ALERT pin.
Bit 5 - ILOW - This bit is set when the Internal Diode channel drops below its programmed low limit.
When set, this bit will assert the ALERT pin.
Bit 4 - EHIGH - This bit is set when the External Diode channel exceeds its programmed high limit.
When set, this bit will assert the ALERT pin.
Bit 3 - ELOW - This bit is set when the External Diode channel drops below its programmed low limit.
When set, this bit will assert the ALERT pin.
Bit 2 - FAULT - This bit is asserted when a diode fault is detected. When set, this bit will assert the
ALERT pin.
Bit 1 - ETHERM - This bit is set when the External Diode channel exceeds the programmed THERM
limit. When set, this bit will assert the THERM pin. This bit will remain set until the THERM pin is
released at which point it will be automatically cleared.
Bit 0 - ITHERM - This bit is set when the Internal Diode channel exceeds the programmed THERM
limit. When set, this bit will assert the THERM pin. This bit will remain set until the THERM pin is
released at which point it will be automatically cleared.
The Configuration Register controls the basic operation of the device. This register is fully accessible
at either address.
Bit 7 - MASK_ALL - Masks the ALERT pin from asserting.
Bit 6 - RUN / STOP - Controls Active/Standby modes.
Bit 5 - ALERT/COMP - Controls the operation of the ALERT pin.
Bit 4 - RECD - Disables the Resistance Error Correction (REC) for External Diode.
Bit 2 - RANGE - Configures the measurement range and data format of the temperature channels.
Configuration Register
‘0’ (default) - The ALERT pin is not masked. If any of the appropriate status bits are set the ALERT
pin will be asserted.
‘1’ - The ALERT pin is masked. It will not be asserted for any interrupt condition unless it is
configured as a secondary THERM pin. The Status Register will be updated normally.
‘0’ (default) - The device is in Active mode and converting on all channels.
‘1’ -The device is in Standby mode and not converting.
‘0’ (default) - The ALERT pin acts as described in
‘1’ - The ALERT pin acts in comparator mode as described in
MASK_ALL bit is ignored.
‘0’ (default)- REC is enabled for the External Diode.
‘1’ - REC is disabled for the External Diode 1.
MASK_
ALL
B7
STOP
RUN/
B6
Table 6.4 Configuration Register
ALERT/
COMP
DATASHEET
B5
26
RECD
Section
B4
5.3.2).
Section
1°C Temperature Sensor with Beta Compensation
B3
-
5.3.
Section
RANGE
B2
5.3.2. In this mode the
DAVG_
DIS
B1
SMSC EMC1402
B0
-
Datasheet
DEFAULT
00h