MCP98243-BE/MC Microchip Technology, MCP98243-BE/MC Datasheet - Page 5

• Manufacturer Part Number: MCP98243-BE/MC
• Description: IC TEMP SENSOR 3V 2WIRE 8-DFN
• Manufacturer: Microchip Technology

Specifications of MCP98243-BE/MC

• Package / Case: 8-DFN
• Output Type: I²C™/SMBus™
• Function: Temp Monitoring System (Sensor)
• Topology: ADC (Sigma Delta), Register Bank
• Sensor Type: Internal
• Sensing Temperature: -40°C ~ 125°C
• Output Alarm: No
• Output Fan: Yes
• Voltage - Supply: 2.7 V ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Full Temp Accuracy: +/- 3 C
• Digital Output - Bus Interface: Serial (2-Wire, I2C)
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• Ic Output Type: Digital
• Sensing Accuracy Range: ± 0.5°C
• Temperature Sensing Range: -40°C To +125°C
• Supply Current: 200µA
• Supply Voltage Range: 2.7V To 5.5V
• Sensor Case Style: DFN
• No. Of Pins: 8
• Rohs Compliant: Yes
• Resolution (bits): 8bit
• Supply Voltage Min: 3V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

SENSOR AND EEPROM SERIAL INTERFACE TIMING SPECIFICATIONS
© 2009 Microchip Technology Inc.
Electrical Specifications: Unless otherwise indicated, GND = Ground, T
(Note 1, 5).
2-Wire I
Serial port frequency
Low Clock
High Clock
Rise time
Fall time
Data in Setup time
Data in Hold time
Data out Hold time
Start Condition Setup time
Start Condition Hold time
Stop Condition Setup time
Bus idle
Time out (Sensor Only)
Bus Capacitive load
Note 1:
2:
3:
4:
5:
6:
Parameters
2
C Interface
All values referred to V
If t
is required for communication.
This device can be used in a Standard-mode I
be met. This device does not stretch SCL Low time. It outputs the next data bit to the SDA line within
t
before the SCL line is released.
As a transmitter, the device provides internal minimum delay time t
region (min. 300 ns) of the falling edge of SCL t
conditions.
For V
biased and consumes 100 µA (typical) until the sensor POR resets and acknowledges a shutdown com-
mand.
As a receiver, SDA should not be sampled at the falling edge of SCL. SDA can transition t
SCL toggles Low.
R MAX
LOW
DD
+ t
> t
ranges of 1.8V to the temperature sensor V
SU:DI MIN
OUT
or t
HIGH
t
= 1000 ns + 250 ns = 1250 ns (according to the Standard-mode I
t
t
t
t
SU:STO
SU:STA
HD:STA
B:FREE
t
t
t
HD:DO
Sym
t
SU:DI
HD:DI
t
f
HIGH
LOW
OUT
SCL
C
t
t
R
F
> t
b
IL MAX
OUT
, the temperature sensor I
V
and V
DD
4700
4000
4700
4000
4000
4700
Min
250
200
10
20
—
—
—
0
= 1.8V to 5.5V V
IH MIN
1000
Max
levels.
100
300
900
—
—
—
—
—
—
—
—
—
—
2
C-bus system, but the requirement t
F MAX
DD
1300
1300
Min
600
100
200
600
600
600
POR_TS
10
20
20
25
—
0
to avoid unintended generation of Start or Stop
= 2.2V to 5.5V
2
C interface will time out. A Repeat Start command
, the temperature sensor becomes partially
Max
A
400
300
300
900
400
35
—
—
—
—
—
—
—
—
= -20°C to +125°C, and C
MCP9843/98243
HD:DAT MIN
Units
kHz
ms
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
pf
to bridge the undefined
Note 2, 4
Note 2
Note 2
Note 3
Note 6
Note 4
V
DD
= 3.0V to 3.6V
SU:DAT
2
C-bus specification)
Conditions
DS22153C-page 5
HD:DI
L
≥ 250 ns must
= 80 pF
0 ns after