TCN75-3.3MUA Microchip Technology, TCN75-3.3MUA Datasheet - Page 21

• Manufacturer Part Number: TCN75-3.3MUA
• Description: IC TEMP SENSOR SRL 3.3V 8MSOP
• Manufacturer: Microchip Technology

Specifications of TCN75-3.3MUA

• Package / Case: 8-MSOP, Micro8™, 8-uMAX, 8-uSOP,
• Output Type: 2-Wire Serial
• Function: Temp Monitoring System (Sensor)
• Topology: ADC (Sigma Delta), Register Bank
• Sensor Type: Internal
• Sensing Temperature: -55°C ~ 125°C
• Output Alarm: Yes
• Output Fan: No
• Voltage - Supply: 2.7 V ~ 5.5 V
• Operating Temperature: -55°C ~ 125°C
• Mounting Type: Surface Mount
• Temperature Threshold: Programmable
• Full Temp Accuracy: 3 C
• Digital Output - Bus Interface: 2-Wire
• Digital Output - Number Of Bits: 9 bit
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.7 V
• Description/function: 2-Wire Serial Input/Output - Thermal Monitors
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 55 C
• Supply Current: 1 mA
• Ic Output Type: Logic
• Sensing Accuracy Range: ± 0.5°C
• Supply Voltage Range: 2.7V To 5.5V
• Sensor Case Style: MSOP
• No. Of Pins: 8
• Filter Terminals: SMD
• Rohs Compliant: Yes
• Accuracy %: 0.5°C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 158-1003; 158-1003

6.0
6.1
The SDA and SCLK serial interface are open-drain pins
that require pull-up resistors. This configuration is
shown in Figure 6-1.
FIGURE 6-1:
Interface.
The TCN75A is designed to meet 0.4V (max.) voltage
drop at 3 mA of current. This allows the TCN75A to
drive lower values of pull-up resistors and higher bus
capacitance. In this application, all devices on the bus
must meet the same pull-down current requirements.
6.2
Microchip provides several microcontroller product
lines with Master Synchronous Serial Port Modules
(MSSP) that include the I
module implements all master and slave functions and
simplifies
Figure 6-2 shows a typical application using the
PIC16F737 as a master to control other Microchip
slave products, such as EEPROM, fan speed
controllers and the TCN75A temperature sensor
connected to the bus.
FIGURE 6-2:
Bus
© 2005 Microchip Technology Inc.
Microcontroller
APPLICATIONS INFORMATION
Connecting to the Serial Bus
Typical Application
PIC16F737
Fan Speed
Controller
the
TC654
firmware
Pull-up Resistors On Serial
Multiple Devices on I
SDA SCLK
V
R
DD
2
development
C interface mode. This
R
SDA
SCLK
Temperature
TCN75A
EEPROM
TCN75A
24LC01
Sensor
overhead.
2
C™
The ALERT output can be wire-ORed with a number of
other open-drain devices. In such applications, the
output needs to be programmed as an active-low
output. Most systems will require pull-up resistors for
this configuration.
6.3
The TCN75A does not require any additional compo-
nents besides the master controller in order to measure
temperature. However, it is recommended that a
decoupling capacitor of 0.1 µF to 1 µF be used
between the V
ceramic capacitor is recommended. It is necessary for
the capacitor to be located as close as possible to the
power pins in order to provide effective noise
protection.
6.4
The TCN75A measures temperature by monitoring the
voltage of a diode located in the die. A low-impedance
thermal path between the die and the Printed Circuit
Board (PCB) is provided by the pins. Therefore, the
TCN75A effectively monitors the temperature of the
PCB. However, the thermal path for the ambient air is
not as efficient because the plastic device package
functions as a thermal insulator.
A potential for self-heating errors can exist if the
TCN75A SDA and SCLK communication lines are
heavily loaded with pull-ups. Typically, the self-heating
error is negligible because of the relatively small
current consumption of the TCN75A. However, in order
to maximize the temperature accuracy, the SDA and
SCLK pins need to be lightly loaded.
Layout Considerations
Thermal Considerations
DD
and GND pins. A high-frequency
TCN75A
DS21935A-page 21