TC9400COD713 Microchip Technology, TC9400COD713 Datasheet - Page 14
![IC V-FREQ/FREQ-V CONV 14SOIC](/photos/6/59/65933/150-14-soic_sml.jpg)
TC9400COD713
Manufacturer Part Number
TC9400COD713
Description
IC V-FREQ/FREQ-V CONV 14SOIC
Manufacturer
Microchip Technology
Type
Volt to Freq & Freq to Voltr
Datasheet
1.TC9402CPD.pdf
(28 pages)
Specifications of TC9400COD713
Frequency - Max
100kHz
Full Scale
±40ppm/°C
Linearity
±0.05%
Mounting Type
Surface Mount
Package / Case
14-SOIC (0.154", 3.90mm Width)
Supply Voltage (max)
15 V
Supply Voltage (min)
8 V
Maximum Operating Temperature
+ 70 C
Minimum Operating Temperature
0 C
Dual Supply Voltage
+/- 5 V
Full Scale Frequency
100 KHz
Linearity Error
+/- 0.25 % FSR
Maximum Dual Supply Voltage
+/- 7.5 V
Minimum Dual Supply Voltage
+/- 4 V
Mounting Style
SMD/SMT
Operating Supply Voltage
9 V, 12 V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
TC9400COD713
Manufacturer:
MICROCHIP
Quantity:
12 000
TC9400/9401/9402
6.0
6.1
The output voltage is related to the input frequency
(F
EQUATION 6-1:
The response time to a change in F
C
proportional to C
C
1 µF to 100 µF are perfectly acceptable for low frequen-
cies.
When the TC9400 is used in the Single Supply mode,
V
and Pin 2.
FIGURE 6-1:
DS21483D-page 14
Frequency
REF
INT
INT
IN
Input
) by the transfer equation:
). The amount of ripple on V
can be increased to lower the ripple. Values of
is defined as the voltage difference between Pin 7
+5V
0V
F/V CONVERTER DESIGN
INFORMATION
Input/Output Relationships
V
OUT
33 kΩ
INT
= [V
and the input frequency.
REF
0.01 µF
Frequency Input Level Shifter.
(a) ±5V Supply
C
REF
IN914
R
INT
] F
IN
1.0
MΩ
OUT
IN
is equal to (R
11
GND
DET
is inversely
TC9400
6
+5V
V
-5V
DD
V
14
4
SS
INT
Frequency
Input
6.2
The input frequency is applied to the Threshold
Detector input (Pin 11). As discussed in the V/F circuit
section of this data sheet, the threshold of Pin 11 is
approximately (V
voltage range extends from V
the threshold. If the voltage on Pin 11 goes more than
2.5 volts below the threshold, the V/F mode start-up
comparator will turn on and corrupt the output voltage.
The Threshold Detector input has about 200 mV of
hysteresis.
In ±5V applications, the input voltage levels for the
TC9400 are ±400 mV, minimum. If the frequency
source being measured is unipolar, such as TTL or
CMOS operating from a +5V source, then an AC
coupled level shifter should be used. One such circuit
is shown in
The level shifter circuit in
single supply F/V applications. The resistor divider
ensures that the input threshold will track the supply
voltages. The diode clamp prevents the input from
going far enough in the negative direction to turn on the
start-up comparator. The diode’s forward voltage
decreases by 2.1 mV/°C, so for high ambient
temperature operation, two diodes in series are
recommended.
+5V
0V
Input Voltage Levels
33 kΩ
Figure
0.01 µF
DD
6-1(a).
+ V
0.1 µF 10 kΩ
IN914
© 2007 Microchip Technology Inc.
SS
Figure
)/2 ±400 mV. Pin 11’s input
(b) Single Supply
10 kΩ
DD
1.0
MΩ
6-1(b) can be used in
to about 2.5V below
11
DET
TC9400
+8V to +15V
V
DD
V
14
4
SS