AD652JP-REEL Analog Devices Inc, AD652JP-REEL Datasheet - Page 22
![IC V-F CONV SYNCH MONO 5V 20PLCC](/photos/6/52/65299/505-20-plcc_sml.jpg)
AD652JP-REEL
Manufacturer Part Number
AD652JP-REEL
Description
IC V-F CONV SYNCH MONO 5V 20PLCC
Manufacturer
Analog Devices Inc
Type
Voltage to Frequencyr
Datasheet
1.AD652JPZ.pdf
(28 pages)
Specifications of AD652JP-REEL
Rohs Status
RoHS non-compliant
Frequency - Max
2MHz
Full Scale
±25ppm/°C
Linearity
±0.005%
Mounting Type
Surface Mount
Package / Case
20-LCC (J-Lead)
Converter Function
VFC
Full Scale Frequency
2000
Power Supply Requirement
Single/Dual
Single Supply Voltage (max)
36V
Single Supply Voltage (min)
12V
Dual Supply Voltage (typ)
±15V
Dual Supply Voltage (min)
±6V
Dual Supply Voltage (max)
±18V
Operating Temperature (min)
0C
Operating Temperature (max)
70C
Operating Temperature Classification
Commercial
Package Type
PLCC
Lead Free Status / Rohs Status
Not Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AD652JP-REEL
Manufacturer:
Analog Devices Inc
Quantity:
10 000
Company:
Part Number:
AD652JP-REEL7
Manufacturer:
Analog Devices Inc
Quantity:
10 000
AD652
ISOLATED FRONT END
In some applications, it may be necessary to have complete
galvanic isolation between the analog signals being measured
and the digital portions of the circuit. The circuit shown in
Figure 32 runs off a single 5 V power supply and provides a self-
contained, completely isolated analog measurement system. The
power for the AD652 SVFC is provided by a chopper and a
transformer, and is regulated to 15 V.
Both the chopper frequency and the AD652 clock frequency are
125 kHz, with the clock signal being relayed to the SVFC
through the transformer. The frequency output signal is relayed
through an opto-isolator and latched into a D flop. The chopper
frequency is generated from an AD654 VFC, and is frequency
divided by two to develop differential drive for the chopper
transistors, and to ensure an accurate 50% duty cycle. The pull-
up resistors on the D flop outputs provide a well-defined high
level voltage to the choppers to equalize the drive in each
direction. The 10 µH inductor in the 5 V lead of the transformer
primary is necessary to equalize any residual imbalance in the
drive on each half cycle, and thus prevent saturation of the core.
The capacitor across the primary resonates the system so that
under light loading conditions on the secondary, the wave shape
is sinusoidal and the clock frequency is relayed to the SVFC. To
adjust the chopper frequency, disconnect any load on the
secondary and tune the AD654 for a minimum in the supply
current drawn from the 5 V supply.
A-TO-D CONVERSION
In performing an A-to-D conversion, the output pulses of a
VFC are counted for a fixed-gate interval. To achieve maximum
performance with the AD652, the fixed-gate interval should be
generated using a multiple of the SVFC clock input. Counting
in this manner eliminates any errors due to the clock (whether
it be jitter, drift with time or temperature, and so on) since it is
the ratio of the clock and output frequencies that is being
measured.
Table
Resolution
12 Bits
12 Bits
12 Bits
4 Digits
14 Bits
14 Bits
14 Bits
4½ Digits
16 Bits
16 Bits
4
.
N
4096
4096
4096
10000
16384
16384
16384
20000
65536
65536
Clock
81.92 kHz
2 MHz
4 MHz
200 kHz
327.68 kHz
1.966 MHz
1.638 MHz
400 kHz
655.36 kHz
4 MHz
Conversion or Gate Time (ms)
100
4.096
2.048
100
100
16.66
20
100
200
32.77
Rev. C | Page 22 of 28
The resolution of the A-to-D conversion measurement is
determined by the clock frequency and the gate time. If, for
instance, a resolution of 12 bits is desired and the clock
frequency is 1 MHz (resulting in an AD652 FS frequency of
500 kHz) the gate time is:
Where N is the total number of codes for a given resolution.
Figure 33 shows the AD652 SVFC as an A-to-D converter in
block diagram form.
To provide the ÷2N block, a single-chip counter such as the
4020B can be used. The 4020B is a 14-stage binary ripple
counter that has a clock and master reset for inputs, and
buffered outputs from the first stage and the last 11 stages. The
output of the first stage is f
of the last stage is f
this single chip counter as the ÷2N block, 13-bit resolution can
be achieved. Higher resolution can be achieved by cascading D-
type flip flops or another 4020B with the counter.
Table 4
time for various degrees of resolution. Note that if the variables
are chosen such that the gate times are multiples of 50 Hz,
60 Hz, or 400 Hz, normal mode rejection (NMR) of those line
frequencies occur.
⎛
⎜ ⎜
⎝
=
FS
Typical Linearity (%)
0.01
0.02
0.002
0.002
0.02
1
0.002
0.002
0.01
0.01
0.002
shows the relationship between clock frequency and gate
8192
×
V
N
IN
Freq
10
Figure 33. Block Diagram of SVFC A-to-D Converter
6
sec
⎞
⎟ ⎟
⎠
1 –
AD652
CLOCK
=
=
CLOCK
. 8
⎛
⎜ ⎜
⎝
192
1
2
Clock
÷ 2
f
OUT
ms
CLOCK
14
N
= f
Freq
INPUT
÷
2N
÷ 2
CLOCK
⎞
⎟ ⎟
⎠
Comments
50 Hz, 60 Hz,400 Hz NMR
50 Hz, 60 Hz, 400 Hz NMR
50 Hz, 60 Hz, 400 Hz NMR
60 Hz NMR
50 Hz NMR
50 Hz, 60 Hz, 400 Hz NMR
50 Hz, 60 Hz, 400 Hz NMR
1
−
= f
1
/16384. Therefore, using
COUNTER
=
CLOCK
⎛
⎜ ⎜
⎝
2
1
GATE
(
MHz
4096
/2, while the output
)
⎞
⎟ ⎟
⎠
TO µP
−
1