TL494BDR2G ON Semiconductor, TL494BDR2G Datasheet - Page 6

• Manufacturer Part Number: TL494BDR2G
• Description: IC PWM CTRLR SWITCHMODE 16-SOIC
• Manufacturer: ON Semiconductor
• Series: SWITCHMODE™r

Specifications of TL494BDR2G

• Pwm Type: Voltage Mode
• Number Of Outputs: 1
• Frequency - Max: 200kHz
• Duty Cycle: 50%
• Voltage - Supply: 7 V ~ 40 V
• Buck: No
• Boost: No
• Flyback: No
• Inverting: No
• Doubler: No
• Divider: No
• Cuk: No
• Isolated: No
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 16-SOIC (3.9mm Width)
• Frequency-max: 200kHz
• Number Of Pwm Outputs: 2
• On/off Pin: No
• Adjustable Output: No
• Topology: Push-Pull
• Switching Freq: 200KHz
• Operating Supply Voltage (max): 40V
• Output Current: 500mA
• Synchronous Pin: No
• Rise Time: 100ns
• Fall Time: 40ns
• Operating Temperature Classification: Automotive
• Mounting: Surface Mount
• Pin Count: 16
• Package Type: SOIC
• Switching Frequency: 200 KHz
• Duty Cycle (max): 48 %
• Operating Supply Voltage: 15 V
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Description
control circuit, incorporating the primary building blocks
required for the control of a switching power supply. (See
Figure 1.) An internal−linear sawtooth oscillator is
frequency− programmable by two external components, R
and C
by:
comparison of the positive sawtooth waveform across
capacitor C
which drive output transistors Q1 and Q2, are enabled only
when the flip−flop clock−input line is in its low state. This
happens only during that portion of time when the sawtooth
voltage is greater than the control signals. Therefore, an
increase in control−signal amplitude causes a corresponding
linear decrease of output pulse width. (Refer to the Timing
Diagram shown in Figure 2.)
the deadtime control, the error amplifier inputs, or the
feedback input. The deadtime control comparator has an
effective 120 mV input offset which limits the minimum
output deadtime to approximately the first 4% of the
sawtooth−cycle time. This would result in a maximum duty
cycle on a given output of 96% with the output control
grounded, and 48% with it connected to the reference line.
Additional deadtime may be imposed on the output by
setting the deadtime−control input to a fixed voltage,
ranging between 0 V to 3.3 V.
for the error amplifiers to adjust the output pulse width from
the maximum percent on−time, established by the deadtime
control input, down to zero, as the voltage at the feedback
pin varies from 0.5 V to 3.5 V. Both error amplifiers have a
The TL494 is a fixed−frequency pulse width modulation
Output pulse width modulation is accomplished by
The control signals are external inputs that can be fed into
The pulse width modulator comparator provides a means
Input/Output
Grounded
Controls
T
@ V
. The approximate oscillator frequency is determined
ref
For more information refer to Figure 3.
T
to either of two control signals. The NOR gates,
Single−ended PWM @ Q1 and Q2
Push−pull Operation
Functional Table
f
osc
Output Function
≈
R
T
1.1
• C
T
APPLICATIONS INFORMATION
f
f
osc
out
TL494, NCV494
http://onsemi.com
1.0
0.5
=
T
6
common mode input range from −0.3 V to (V
may be used to sense power−supply output voltage and
current. The error−amplifier outputs are active high and are
ORed together at the noninverting input of the pulse−width
modulator comparator. With this configuration, the
amplifier that demands minimum output on time, dominates
control of the loop.
generated on the output of the deadtime comparator, which
clocks the pulse−steering flip−flop and inhibits the output
transistors, Q1 and Q2. With the output−control connected
to the reference line, the pulse−steering flip−flop directs the
modulated pulses to each of the two output transistors
alternately for push−pull operation. The output frequency is
equal to half that of the oscillator. Output drive can also be
taken from Q1 or Q2, when single−ended operation with a
maximum on−time of less than 50% is required. This is
desirable when the output transformer has a ringback
winding with a catch diode used for snubbing. When higher
output−drive currents are required for single−ended
operation, Q1 and Q2 may be connected in parallel, and the
output−mode pin must be tied to ground to disable the
flip−flop. The output frequency will now be equal to that of
the oscillator.
sourcing up to 10 mA of load current for external bias
circuits. The reference has an internal accuracy of $5.0%
with a typical thermal drift of less than 50 mV over an
operating temperature range of 0° to 70°C.
500 k
100 k
When capacitor C
The TL494 has an internal 5.0 V reference capable of
1.0 k
10 k
500
1.0 k 2.0 k 5.0 k
Figure 3. Oscillator Frequency versus
T
R
10 k 20 k 50 k
T,
Timing Resistance
is discharged, a positive pulse is
TIMING RESISTANCE (W)
0.1 mF
0.01 mF
C
T
= 0.001 mF
100 k 200 k
V
CC
CC
= 15 V
− 2V), and
500 k 1.0 M