UC2842BNG ON Semiconductor, UC2842BNG Datasheet - Page 9

• Manufacturer Part Number: UC2842BNG
• Description: IC CTRLR CURRENT MODE HP 8-DIP
• Manufacturer: ON Semiconductor

Specifications of UC2842BNG

• Pwm Type: Current Mode
• Number Of Outputs: 1
• Frequency - Max: 275kHz
• Duty Cycle: 96%
• Voltage - Supply: 11 V ~ 25 V
• Buck: No
• Boost: Yes
• Flyback: Yes
• Inverting: No
• Doubler: No
• Divider: No
• Cuk: No
• Isolated: Yes
• Operating Temperature: -25°C ~ 85°C
• Package / Case: 8-DIP (0.300", 7.62mm)
• Frequency-max: 275kHz
• Duty Cycle (max): 96 %
• Output Voltage: 4.95 V to 5.05 V
• Output Current: 1000 mA
• Mounting Style: Through Hole
• Switching Frequency: 500 KHz
• Operating Supply Voltage: 30 V
• Maximum Operating Temperature: + 85 C
• Fall Time: 50 ns
• Minimum Operating Temperature: - 25 C
• Rise Time: 50 ns
• Synchronous Pin: No
• Topology: Boost, Flyback, Forward
• Number Of Pwm Outputs: 1
• On/off Pin: No
• Adjustable Output: No
• Switching Freq: 500kHz
• Operating Supply Voltage (max): 30V
• Operating Temperature Classification: Commercial
• Mounting: Through Hole
• Pin Count: 8
• Package Type: PDIP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Error Amplifier
inverting input and output is provided. It features a typical
DC voltage gain of 90 dB, and a unity gain bandwidth of
1.0 MHz with 57 degrees of phase margin (Figure 8). The
non−inverting input is internally biased at 2.5 V and is not
pinned out. The converter output voltage is typically divided
down and monitored by the inverting input. The maximum
input bias current is −2.0 mA which can cause an output
voltage error that is equal to the product of the input bias
current and the equivalent input divider source resistance.
loop compensation (Figure 33). The output voltage is offset
by two diode drops (≈1.4 V) and divided by three before it
connects to the non−inverting input of the Current Sense
Comparator. This guarantees that no drive pulses appear at
the Output (Pin 6) when pin 1 is at its lowest state (V
This occurs when the power supply is operating and the load
is removed, or at the beginning of a soft−start interval
(Figures 25, 26). The Error Amp minimum feedback
resistance is limited by the amplifier’s source current
(0.5 mA) and the required output voltage (V
comparator’s 1.0 V clamp level:
Current Sense Comparator and PWM Latch
controller, whereby output switch conduction is initiated by
the oscillator and terminated when the peak inductor current
reaches the threshold level established by the Error
Amplifier Output/Compensation (Pin 1). Thus the error
signal controls the peak inductor current on a
cycle−by−cycle basis. The Current Sense Comparator PWM
Latch configuration used ensures that only a single pulse
A fully compensated Error Amplifier with access to the
The Error Amp Output (Pin 1) is provided for external
The UC3842B, UC3843B operate as a current mode
R
f(min)
≈
3.0 (1.0 V) + 1.4 V
0.5 mA
= 8800 W
OH
) to reach the
http://onsemi.com
OL
).
9
appears at the Output during any given oscillator cycle. The
inductor current is converted to a voltage by inserting the
ground−referenced sense resistor R
source of output switch Q1. This voltage is monitored by the
Current Sense Input (Pin 3) and compared to a level derived
from the Error Amp Output. The peak inductor current under
normal operating conditions is controlled by the voltage at
pin 1 where:
supply output is overloaded or if output voltage sensing is
lost. Under these conditions, the Current Sense Comparator
threshold will be internally clamped to 1.0 V. Therefore the
maximum peak switch current is:
becomes desirable to reduce the internal clamp voltage in
order to keep the power dissipation of R
level. A simple method to adjust this voltage is shown in
Figure 24. The two external diodes are used to compensate
the internal diodes, yielding a constant clamp voltage over
temperature. Erratic operation due to noise pickup can result
if there is an excessive reduction of the I
voltage.
waveform can usually be observed and may cause the power
supply to exhibit an instability when the output is lightly
loaded. This spike is due to the power transformer
interwinding capacitance and output rectifier recovery time.
The addition of an RC filter on the Current Sense Input with
a time constant that approximates the spike duration will
usually eliminate the instability (refer to Figure 28).
Abnormal operating conditions occur when the power
When designing a high power switching regulator it
A narrow spike on the leading edge of the current
I
pk
I
pk(max)
=
V
(Pin 1)
=
3 R
− 1.4 V
1.0 V
S
R
S
S
in series with the
S
to a reasonable
pk(max)
clamp