GNM314R72A102KD01D Murata Electronics North America, GNM314R72A102KD01D Datasheet - Page 48

• Manufacturer Part Number: GNM314R72A102KD01D
• Description: CAP 4-ARRAY 1000PF 100V X7R 1206
• Manufacturer: Murata Electronics North America
• Series: GNMr

Specifications of GNM314R72A102KD01D

• Capacitance: 1000pF
• Voltage - Rated: 100V
• Dielectric Material: Ceramic
• Number Of Capacitors: 4
• Circuit Type: Isolated
• Temperature Coefficient: X7R
• Tolerance: ±10%
• Mounting Type: Surface Mount
• Package / Case: 1206 (3216 Metric)
• Height: 0.031" (0.80mm)
• Size / Dimension: 0.126" L x 0.063" W (3.20mm x 1.60mm)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 490-3421-2

7
!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
46
No.
12
13
14
15
16
17
GNM Series Specifications and Test Methods (2)
Continued from the preceding page.
Resistance
to Soldering
Heat
Deflection
Solderability of
Termination
Temperature
Cycle
High
Temperature
High
Humidity
(Steady)
Durability
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Item
Appearance
Capacitance
Change
D.F.
I.R.
Dielectric
Strength
Appearance
Capacitance
Change
D.F.
I.R.
Dielectric
Strength
Appearance
Capacitance
Change
D.F.
I.R.
Dielectric
Strength
Appearance
Capacitance
Change
D.F.
I.R.
Dielectric
Strength
No cracking or marking defects should occur.
75% of the terminations are to be soldered evenly
and continuously.
No marking defects
R6: Within T7.5%
0.1 max.
50Ω · F min.
No failure
No marking defects
R6: Within T12.5%
0.1 max.
50Ω · F min.
No failure
No marking defects
R6: Within T12.5%
0.2 max.
12.5Ω · F min.
No failure
No marking defects
R6: Within T12.5%
0.2 max.
25Ω · F min.
No failure
R230
45
Capacitance meter
Fig. 3
Specifications
20
50
Pressurize
45
Pressurizing
speed : 1.0mm/sec.
Flexure : V1
Solder the capacitor to the test jig (glass epoxy board) shown in
Fig. 2 using a eutectic solder. Then apply a force in the
direction shown in Fig. 3. The soldering should be done by the
reflow method and should be conducted with care so that the
soldering is uniform and free of defects such as heat shock.
Immerse the capacitor in a solution of ethanol (JIS-K-8101) and
rosin (JIS-K-5902) (25% rosin in weight proportion). Preheat at
80 to 120°C for 10 to 30 seconds. After preheating, immerse in
eutectic solder solution for 2T0.5 seconds at 230T5°C or
Sn-3.0Ag-0.5Cu solder solution for 2T0.5 seconds at 245T5°C.
Preheat the capacitor at 120 to 150°C for 1 minute. Immerse
the capacitor in a eutectic solder or Sn-3.0Ag-0.5Cu solder
solution at 270T5°C for 10T0.5 seconds.
Let sit at room temperature for 24T2 hours, then measure.
• Initial measurement
Fix the capacitor to the supporting jig in the same manner and
under the same conditions as (10).
Perform the five cycles according to the four heat treatments
listed in the following table.
Let sit for 24T2 hours at room temperature, then measure.
• Initial measurement
Apply the rated voltage at 40T2°C and 90 to 95% humidity for
500T12 hours. The charge/discharge current is less than 50mA.
• Initial measurement
• Measurement after test
Apply 125% of the rated voltage for 1000T12 hours at the
maximum operating temperature T3°C. Let sit for 24T2 hours
at room temperature, then measure.
The charge/discharge current is less than 50mA.
• Initial measurement
• Measurement after test
Perform a heat treatment at 150 +0/-10°C for one hour and
then let sit for 24T2 hours at room temperature. Perform
the initial measurement.
Perform a heat treatment at 150 +0/-10 °C for one hour and
then let sit for 24T2 hours at room temperature.
Perform the initial measurement.
Perform a heat treatment at 150 +0/-10°C for one hour
and then let sit for 24T2 hours at room temperature.
Perform the initial measurement.
Perform a heat treatment at 150 +0/-10°C for one hour
and then let sit for 24T2 hours at room temperature, then
measure.
Perform a heat treatment at 150 +0/-10°C for one hour
and then let sit for 24T2 hours at room temperature.
Perform the initial measurement.
Perform a heat treatment at 150 +0/-10°C for one hour
and then let sit for 24T2 hours at room temperature, then
measure.
Temp. (D)
Time (min.)
GNM1M2
Step
GNM212
Type
Min. Operating
5.0
d
a
b
Temp.
30T3
c
2.0T0.05
2.0T0.5
1
a
100
1.0
Test Method
Fig. 2
Temp.
Room
0.5T0.05
0.6T0.05
2 to 3
2
b
Max. Operating
0.32T0.05
0.5T0.05
Temp.
30T3
Thickness: 0.8mm
3
c
0.32T0.05
0.5T0.05
Temp.
(in mm)
Room
2 to 3
d
4
C02E.pdf
07.2.6