MAX1748EUE+ Maxim Integrated Products, MAX1748EUE+ Datasheet - Page 8
![IC DC-DC CONV TRPL LCD 16-TSSOP](/photos/6/56/65666/175-16-tssop_sml.jpg)
MAX1748EUE+
Manufacturer Part Number
MAX1748EUE+
Description
IC DC-DC CONV TRPL LCD 16-TSSOP
Manufacturer
Maxim Integrated Products
Datasheet
1.MAX1748EUE.pdf
(16 pages)
Specifications of MAX1748EUE+
Applications
Converter, TFT, LCD
Voltage - Input
2.7 ~ 5.5 V
Number Of Outputs
3
Voltage - Output
2.7 ~ 13 V
Operating Temperature
0°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
16-TSSOP
Output Voltage
13 V
Output Current
0.5 A
Input Voltage
5.5 V
Supply Current
1 mA
Switching Frequency
1000 KHz
Mounting Style
SMD/SMT
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Meter Display Type
LCD
Supply Voltage Range
2.7V To 5.5V
Driver Case Style
TSSOP
No. Of Pins
16
Operating Temperature Range
-40°C To +85°C
Output Voltage Min
2.7V
Rohs Compliant
Yes
Input Voltage Max
5.5V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
The MAX1748/MAX8726 are highly efficient triple-output
power supplies for TFT-LCD applications. These devices
contain one high-power step-up converter and two low-
power charge pumps. The primary boost converter uses
an internal n-channel MOSFET to provide maximum
efficiency and to minimize the number of external compo-
nents. The output voltage of the main boost converter
(V
The dual charge pumps independently regulate a posi-
tive output (V
low-power outputs use external diode and capacitor
stages (as many stages as required) to regulate output
voltages up to +40V and down to -40V. A proprietary
regulation algorithm minimizes output ripple as well as
capacitor sizes for both charge pumps.
Also included in the MAX1748/MAX8726 is a precision
1.25V reference that sources up to 50µA, logic shut-
down, soft-start, power-up sequencing, fault detection,
and an active-low open-drain ready output.
The MAX1748/MAX8726 main step-up converter
switches at a constant 1MHz internal oscillator frequen-
cy to allow the use of small inductors and output
capacitors. The MOSFET switch pulse width is modulat-
ed to control the power transferred on each switching
cycle and to regulate the output voltage.
During PWM operation, the internal clock’s rising edge
sets a flip-flop, which turns on the n-channel MOSFET
(Figure 1). The switch turns off when the sum of the
voltage-error, slope-compensation, and current-feed-
back signals trips the multi-input comparator and
resets the flip-flop. The switch remains off for the rest of
the clock cycle. Changes in the output-voltage error
Triple-Output TFT-LCD
DC-DC Converters
8
MAIN
_______________________________________________________________________________________
PIN
10
11
12
13
14
15
16
8
9
) can be set from V
POS
NAME
SHDN
DRVN
PGND
TGND
SUPN
DRVP
SUPP
) and a negative output (V
FBN
LX
Detailed Description
IN
Active-Low Logic-Level Shutdown Input. Connect SHDN to IN for normal operation.
Main Boost Regulator Power MOSFET n-Channel Drain. Connect output diode and output capacitor
as close to PGND as possible.
Negative Charge-Pump Regulator Feedback Input. Regulates to 0V nominal.
Negative Charge-Pump Driver Output. Output high level is V
Negative Charge-Pump Driver Supply Voltage. Bypass to PGND with a 0.1µF capacitor.
Positive Charge-Pump Driver Output. Output high level is V
Positive Charge-Pump Driver Supply Voltage. Bypass to PGND with a 0.1µF capacitor.
Power Ground. Connect to GND underneath the IC.
Must be connected to ground.
to 13V with external resistors.
Main Boost Converter
NEG
). These
signal shift the switch current trip level, consequently
modulating the MOSFET duty cycle.
The MAX1748/MAX8726 contain two individual low-
power charge pumps. One charge pump inverts the
supply voltage (SUPN) and provides a regulated nega-
tive output voltage. The second charge pump doubles
the supply voltage (SUPP) and provides a regulated
positive output voltage. The MAX1748/MAX8726 con-
tain internal p-channel and n-channel MOSFETs to con-
trol the power transfer. The internal MOSFETs switch at
a constant 500kHz (0.5 x f
During the first half-cycle, the p-channel MOSFET turns
on and the flying capacitor C5 charges to V
diode drop (Figure 2). During the second half-cycle, the
p-channel MOSFET turns off, and the n-channel MOSFET
turns on, level shifting C5. This connects C5 in parallel
with the reservoir capacitor C6. If the voltage across C6
minus a diode drop is lower than the voltage across C5,
charge flows from C5 to C6 until the diode (D5) turns off.
The amount of charge transferred to the output is
controlled by the variable n-channel on-resistance.
During the first half-cycle, the n-channel MOSFET turns
on and charges the flying capacitor C3 (Figure 3). This
initial charge is controlled by the variable n-channel on-
resistance. During the second half-cycle, the n-channel
MOSFET turns off and the p-channel MOSFET turns on,
level shifting C3 by V
allel with the reservoir capacitor C4. If the voltage across
C4 plus a diode drop (V
level-shifted flying capacitor voltage (V
charge flows from C3 to C4 until the diode (D3) turns off.
FUNCTION
Pin Description (continued)
SUPP
SUPN
Dual Charge-Pump Regulator
SUPP
, and low level is PGND.
, and low level is PGND.
POS
OSC
volts. This connects C3 in par-
+ V
).
DIODE
Negative Charge Pump
Positive Charge Pump
) is smaller than the
C3
SUPN
+ V
minus a
SUPP
),