LT1956EGN#PBF Linear Technology, LT1956EGN#PBF Datasheet - Page 3
![IC SW REG STP-DWN HI VOLT 16SSOP](/photos/6/59/65965/161-16-ssop_sml.jpg)
LT1956EGN#PBF
Manufacturer Part Number
LT1956EGN#PBF
Description
IC SW REG STP-DWN HI VOLT 16SSOP
Manufacturer
Linear Technology
Type
Step-Down (Buck)r
Datasheet
1.LT1956EGNPBF.pdf
(28 pages)
Specifications of LT1956EGN#PBF
Internal Switch(s)
Yes
Synchronous Rectifier
No
Number Of Outputs
1
Voltage - Output
1.2 ~ 45 V
Current - Output
1.5A
Frequency - Switching
500kHz
Voltage - Input
5.5 ~ 60 V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
16-SSOP
Primary Input Voltage
60V
No. Of Outputs
1
Output Voltage
68V
Output Current
1.2A
No. Of Pins
16
Operating Temperature Range
-40°C To +125°C
Msl
MSL 1 - Unlimited
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Power - Output
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
ELECTRICAL CHARACTERISTICS
The
V
PARAMETER
Switch Current Limit
Switch On Resistance
Maximum Switch Duty Cycle
Switch Frequency
f
f
Minimum Input Voltage
Minimum Boost Voltage
Boost Current (Note 5)
Input Supply Current (I
Output Supply Current (I
Shutdown Supply Current
Lockout Threshold
Shutdown Thresholds
Minimum SYNC Amplitude
SYNC Frequency Range
SYNC Input Resistance
Note 1: Absolute Maximum Ratings are those values beyond which the life
of a device may be impaired.
Note 2: Gain is measured with a V
clamp level to 200mV below the upper clamp level.
Note 3: Minimum input voltage is not measured directly, but is guaranteed
by other tests. It is defined as the voltage where internal bias lines are still
regulated so that the reference voltage and oscillator remain constant.
Actual minimum input voltage to maintain a regulated output will depend
upon output voltage and load current. See Applications Information.
Note 4: This is the minimum voltage across the boost capacitor needed to
guarantee full saturation of the internal power switch.
Note 5: Boost current is the current flowing into the BOOST pin with the
pin held 5V above input voltage. It flows only during switch on time.
Note 6: Input supply current is the quiescent current drawn by the input
pin when the BIAS pin is held at 5V with switching disabled. Bias supply
current is the current drawn by the BIAS pin when the BIAS pin is held at
5V. Total input referred supply current is calculated by summing input
supply current (I
with V
SW
SW
IN
I
Line Regulation
Shifting Threshold
= 15V, V
TOTAL
IN
denotes specifications which apply over the full operating temperature range, otherwise specifications are at T
= 15V, V
= I
VIN
C
= 1.5V, SHDN = 1V, Boost o/c, SW o/c, unless otherwise noted.
VIN
+ (I
OUT
) with a fraction of supply current (I
BIAS
= 5V, I
VIN
)(V
BIAS
)
OUT
VIN
)
/V
= 1.4mA, I
IN
C
)
swing equal to 200mV above the low
BIAS
= 2.9mA, I
BIAS
CONDITIONS
V
I
FB = 1V or V
V
5.5V V
Df = 10kHz
(Note 3)
(Note 4) I
Boost = V
Boost = V
(Note 6) V
(Note 6) V
SHDN = 0V, V
V
V
V
TOTAL
SW
C
C
C
C
C
):
Open, Boost = V
Set to Give DC = 50%
Open
Open, Shutting Down
Open, Starting Up
= 1.5A, Boost = V
= 2.4mA.
IN
SW
IN
IN
BIAS
BIAS
+ 5V, I
+ 5V, I
SENSE
60V
IN
= 5V
= 5V
1.5A
60V, SW = 0V, V
= 4.1V
SW
SW
IN
IN
+ 5V, FB = 1V or V
= 0.5A
= 1.5A
Note 7: Switch on resistance is calculated by dividing V
the forced current (1.5A). See Typical Performance Characteristics for the
graph of switch voltage at other currents.
Note 8: The LT1956EFE/LT1956EFE-5/LT1956EGN/LT1956EGN-5 are
guaranteed to meet performance specifications from 0 C to 125 C
junction temperature. Specifications over the –40 C to 125 C operating
junction temperature range are assured by design, characterization and
correlation with statistical process controls. The LT1956IFE/LT1956IFE-5/
LT1956IGN/LT1956IGN-5 are guaranteed over the full – 40 C to 125 C
operating junction temperature range.
Note 9: Transconductance and voltage gain refer to the internal amplifier
exclusive of the voltage divider. To calculate gain and transconductance,
refer to the SENSE pin on fixed voltage parts. Divide values shown by the
ratio V
Note 10: This IC includes overtemperature protection that is intended to
protect the device during momentary overload conditions. Junction
temperature will exceed 125 C when overtemperature protection is active.
Continuous operation above the specified maximum operating junction
temperature may impair device reliability.
+ 5V (Note 7)
OUT
/1.219.
C
Open
SENSE
= 4.1V
LT1956/LT1956-5
2.30
0.15
0.25
MIN
460
430
580
1.5
82
75
0.05
2.42
0.37
0.45
TYP
500
0.2
0.8
4.6
1.4
2.9
1.5
90
90
12
42
25
20
2
2
J
IN
MAX
= 25 C.
0.15
2.53
540
570
200
700
0.4
5.5
2.2
4.2
0.6
0.6
2.2
0.3
25
70
75
to SW voltage by
3
3
UNITS
3
1956f
%/V
kHz
kHz
kHz
mA
mA
mA
mA
k
%
%
A
V
V
V
A
A
V
V
V
V