LM3488MM/NOPB National Semiconductor, LM3488MM/NOPB Datasheet - Page 12
![IC CTRLR SWITCH REG N-CH 8-MSOP](/photos/6/57/65756/pkg_mua08a_sml.jpg)
LM3488MM/NOPB
Manufacturer Part Number
LM3488MM/NOPB
Description
IC CTRLR SWITCH REG N-CH 8-MSOP
Manufacturer
National Semiconductor
Type
Step-Up (Boost), Flyback, Sepicr
Datasheet
1.LM3488MMNOPB.pdf
(24 pages)
Specifications of LM3488MM/NOPB
Internal Switch(s)
No
Synchronous Rectifier
No
Number Of Outputs
1
Voltage - Output
Adj to 1.26V
Current - Output
1A
Frequency - Switching
100kHz ~ 1MHz
Voltage - Input
2.97 ~ 40 V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
8-MSOP, Micro8™, 8-uMAX, 8-uSOP,
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Power - Output
-
Other names
LM3488MM
LM3488MM
LM3488MMTR
LM3488MM
LM3488MMTR
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LM3488MM/NOPB
Manufacturer:
TI
Quantity:
15 540
www.national.com
FREQUENCY ADJUST/SYNCHRONIZATION/SHUTDOWN
The switching frequency of LM3488 can be adjusted between
100kHz and 1MHz using a single external resistor. This re-
sistor must be connected between FA/SYNC/SD pin and
ground, as shown in
formance characteristics to determine the value of the resistor
required for a desired switching frequency.
The LM3488 can be synchronized to an external clock. The
external clock must be connected to the FA/SYNC/SD pin
through a resistor, R
this resistor is dependent on the off time of the synchroniza-
tion pulse, T
be used for a given T
OFF(SYNC)
FIGURE 5. ΔV
SYNC
Figure
.
OFF(SYNC)
Table 1
as shown in
6. Please refer to the typical per-
shows the range of resistors to
.
SL
vs R
Figure
SL
7. The value of
FIGURE 6. Frequency Adjust
10138851
12
It is also necessary to have the width of the synchronization
pulse narrower than the duty cycle of the converter. It is also
necessary to have the synchronization pulse width
300nsecs.
The FA/SYNC/SD pin also functions as a shutdown pin. If a
high signal (refer to the electrical characteristics for definition
of high signal) appears on the FA/SYNC/SD pin, the LM3488
stops switching and goes into a low current mode. The total
supply current of the IC reduces to less than 10µA under these
conditions.
Figure 8
tion when operating in Frequency adjust mode and synchro-
nization mode respectively. In frequency adjust mode,
connecting the FA/SYNC/SD pin to ground forces the clock
to run at a certain frequency. Pulling this pin high shuts down
the IC. In frequency adjust or synchronization mode, a high
signal for more than 30µs shuts down the IC.
T
and
OFF(SYNC)
Figure 9
10
1
2
3
4
5
6
7
8
9
(µsec)
show implementation of shutdown func-
TABLE 1.
R
10138816
SYNC
100 to 160
120 to 190
135 to 215
150 to 240
70 to 110
85 to 140
20 to 40
40 to 65
55 to 90
5 to 13
range (kΩ)
≥