LM2678S-ADJ/NOPB National Semiconductor, LM2678S-ADJ/NOPB Datasheet - Page 11
![no-image](/images/manufacturer_photos/0/4/469/national_semiconductor_sml.jpg)
LM2678S-ADJ/NOPB
Manufacturer Part Number
LM2678S-ADJ/NOPB
Description
IC REG SIMPLE SWITCHER TO-263-7
Manufacturer
National Semiconductor
Series
SIMPLE SWITCHER®r
Type
Step-Down (Buck)r
Datasheet
1.LM2678SD-3.3NOPB.pdf
(26 pages)
Specifications of LM2678S-ADJ/NOPB
Internal Switch(s)
Yes
Synchronous Rectifier
No
Number Of Outputs
1
Voltage - Output
1.2 ~ 37 V
Current - Output
5A
Frequency - Switching
260kHz
Voltage - Input
8 ~ 40 V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
D²Pak, TO-263 (7 leads + tab)
Primary Input Voltage
40V
No. Of Outputs
1
Output Voltage
37V
Output Current
5A
No. Of Pins
7
Operating Temperature Range
-40°C To +125°C
Msl
MSL 3 - 168 Hours
Supply Voltage Range
8V To 40V
Rohs Compliant
Yes
Filter Terminals
SMD
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Power - Output
-
Other names
*LM2678S-ADJ
*LM2678S-ADJ/NOPB
LM2678S-ADJ
*LM2678S-ADJ/NOPB
LM2678S-ADJ
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Power supply design using the LM2678 is greatly simplified
by using recommended external components. A wide range
of inductors, capacitors and Schottky diodes from several
manufacturers have been evaluated for use in designs that
cover the full range of capabilities (input voltage, output volt-
age and load current) of the LM2678. A simple design proce-
dure using nomographs and component tables provided in
this data sheet leads to a working design with very little effort.
Alternatively, the design software, LM267X Made Simple
(version 6.0), can also be used to provide instant component
selection, circuit performance calculations for evaluation, a
bill of materials component list and a circuit schematic.
INDUCTOR
The inductor is the key component in a switching regulator.
For efficiency the inductor stores energy during the switch ON
time and then transfers energy to the load while the switch is
OFF.
Nomographs are used to select the inductance value required
for a given set of operating conditions. The nomographs as-
sume that the circuit is operating in continuous mode (the
current flowing through the inductor never falls to zero). The
magnitude of inductance is selected to maintain a maximum
ripple current of 30% of the maximum load current. If the ripple
current exceeds this 30% limit the next larger value is select-
ed.
The inductors offered have been specifically manufactured to
provide proper operation under all operating conditions of in-
put and output voltage and load current. Several part types
are offered for a given amount of inductance. Both surface
mount and through-hole devices are available. The inductors
from each of the three manufacturers have unique character-
istics.
Renco: ferrite stick core inductors; benefits are typically low-
est cost and can withstand ripple and transient peak currents
above the rated value. These inductors have an external
magnetic field, which may generate EMI.
Pulse Engineering: powdered iron toroid core inductors;
these also can withstand higher than rated currents and, be-
ing toroid inductors, will have low EMI.
Coilcraft: ferrite drum core inductors; these are the smallest
physical size inductors and are available only as surface
mount components. These inductors also generate EMI but
less than stick inductors.
FIGURE 2. Basic circuit for adjustable output voltage applications
11
The individual components from the various manufacturers
called out for use are still just a small sample of the vast array
of components available in the industry. While these compo-
nents are recommended, they are not exclusively the only
components for use in a design. After a close comparison of
component specifications, equivalent devices from other
manufacturers could be substituted for use in an application.
Important considerations for each external component and an
explanation of how the nomographs and selection tables were
developed follows.
OUTPUT CAPACITOR
The output capacitor acts to smooth the dc output voltage and
also provides energy storage. Selection of an output capaci-
tor, with an associated equivalent series resistance (ESR),
impacts both the amount of output ripple voltage and stability
of the control loop.
The output ripple voltage of the power supply is the product
of the capacitor ESR and the inductor ripple current. The ca-
pacitor types recommended in the tables were selected for
having low ESR ratings.
In addition, both surface mount tantalum capacitors and
through-hole aluminum electrolytic capacitors are offered as
solutions.
Impacting frequency stability of the overall control loop, the
output capacitance, in conjunction with the inductor, creates
a double pole inside the feedback loop. In addition the ca-
pacitance and the ESR value create a zero. These frequency
response effects together with the internal frequency com-
pensation circuitry of the LM2678 modify the gain and phase
shift of the closed loop system.
As a general rule for stable switching regulator circuits it is
desired to have the unity gain bandwidth of the circuit to be
limited to no more than one-sixth of the controller switching
frequency. With the fixed 260KHz switching frequency of the
LM2678, the output capacitor is selected to provide a unity
gain bandwidth of 40KHz maximum. Each recommended ca-
pacitor value has been chosen to achieve this result.
In some cases multiple capacitors are required either to re-
duce the ESR of the output capacitor, to minimize output
ripple (a ripple voltage of 1% of Vout or less is the assumed
performance condition), or to increase the output capacitance
www.national.com
10088608