LM2586T-ADJ/NOPB National Semiconductor, LM2586T-ADJ/NOPB Datasheet - Page 11
![IC REG SIMPLE SWITCHER TO-220-7](/photos/7/1/70182/14-to-220-7_staggered_and_bent_sml.jpg)
LM2586T-ADJ/NOPB
Manufacturer Part Number
LM2586T-ADJ/NOPB
Description
IC REG SIMPLE SWITCHER TO-220-7
Manufacturer
National Semiconductor
Series
SIMPLE SWITCHER®r
Type
Step-Up (Boost), Flyback, Forward Converterr
Datasheet
1.LM2586S-ADJNOPB.pdf
(30 pages)
Specifications of LM2586T-ADJ/NOPB
Internal Switch(s)
Yes
Synchronous Rectifier
No
Number Of Outputs
1
Voltage - Output
Adjustable
Current - Output
3A
Frequency - Switching
100kHz ~ 200kHz
Voltage - Input
4 ~ 40 V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Through Hole
Package / Case
TO-220-7 (Bent and Staggered Leads)
Dc To Dc Converter Type
Step Up
Pin Count
7 +Tab
Input Voltage
40V
Output Voltage
1.23V
Switching Freq
100 TO 200KHz
Output Current
3A
Efficiency
93%
Package Type
TO-220
Output Type
Adjustable
Switching Regulator
Yes
Load Regulation
100mV
Line Regulation
100mV
Mounting
Through Hole
Input Voltage (min)
4V
Operating Temperature Classification
Automotive
For Use With
551011367-051 - BOARD WEBENCH BUILD IT LM2586/88
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Power - Output
-
Lead Free Status / Rohs Status
Compliant
Other names
*LM2586T-ADJ
*LM2586T-ADJ/NOPB
LM2586T-ADJ
*LM2586T-ADJ/NOPB
LM2586T-ADJ
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Block Diagram
For Fixed Versions
3.3V, R1 = 3.4k, R2 = 2k
5.0V, R1 = 6.15k, R2 = 2k
12V, R1 = 8.73k, R2 = 1k
For Adj. Version
R1 = Short (0Ω), R2 = Open
Flyback Regulator Operation
The LM2586 is ideally suited for use in the flyback regulator
topology. The flyback regulator can produce a single output
voltage, such as the one shown in Figure 4, or multiple
output voltages. In Figure 4, the flyback regulator generates
an output voltage that is inside the range of the input voltage.
This feature is unique to flyback regulators and cannot be
duplicated with buck or boost regulators.
The operation of a flyback regulator is as follows (refer to
Figure 4): when the switch is on, current flows through the
primary winding of the transformer, T1, storing energy in the
magnetic field of the transformer. Note that the primary and
secondary windings are out of phase, so no current flows
through the secondary when current flows through the pri-
mary. When the switch turns off, the magnetic field col-
FIGURE 3. Block Diagram
11
lapses, reversing the voltage polarity of the primary and
secondary windings. Now rectifier D1 is forward biased and
current flows through it, releasing the energy stored in the
transformer. This produces voltage at the output.
The output voltage is controlled by modulating the peak
switch current. This is done by feeding back a portion of the
output voltage to the error amp, which amplifies the differ-
ence between the feedback voltage and a 1.230V reference.
The error amp output voltage is compared to a ramp voltage
proportional to the switch current (i.e., inductor current dur-
ing the switch on time). The comparator terminates the
switch on time when the two voltages are equal, thereby
controlling the peak switch current to maintain a constant
output voltage.
www.national.com
01251623