LT1576IS8#TR Linear Technology, LT1576IS8#TR Datasheet - Page 10
![IC REG SW ADJ 1.5A STEPDWN 8SOIC](/photos/6/62/66297/8-soic_05-08-1610_sml.jpg)
LT1576IS8#TR
Manufacturer Part Number
LT1576IS8#TR
Description
IC REG SW ADJ 1.5A STEPDWN 8SOIC
Manufacturer
Linear Technology
Type
Step-Down (Buck)r
Datasheet
1.LT1576CS8PBF.pdf
(28 pages)
Specifications of LT1576IS8#TR
Internal Switch(s)
Yes
Synchronous Rectifier
No
Number Of Outputs
1
Voltage - Output
Adj to 1.2V
Current - Output
1.5A
Frequency - Switching
200kHz
Voltage - Input
5 ~ 25 V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
8-SOIC (3.9mm Width)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Power - Output
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
LT1576/LT1576-5
APPLICATIONS
The internal circuitry which forces reduced switching
frequency also causes current to flow out of the feedback
pin when output voltage is low. The equivalent circuitry is
shown in Figure 2. Q1 is completely off during normal
operation. If the FB pin falls below 0.7V, Q1 begins to
conduct current and reduces frequency at the rate of
approximately 1kHz/ A. To ensure adequate frequency
foldback (under worst-case short-circuit conditions), the
external divider Thevinin resistance must be low enough
to pull 35 A out of the FB pin with 0.5V on the pin (R
14.3k). The net result is that reductions in frequency and
current limit are affected by output voltage divider imped-
ance. Although divider impedance is not critical, caution
should be used if resistors are increased beyond the
suggested values and short-circuit conditions will occur
with high input voltage. High frequency pickup will
increase and the protection accorded by frequency and
current foldback will decrease.
MAXIMUM OUTPUT LOAD CURRENT
Maximum load current for a buck converter is limited by
the maximum switch current rating (I
This current rating is 1.5A up to 50% duty cycle (DC),
decreasing to 1.3A at 80% duty cycle. This is shown
graphically in Typical Performance Characteristics and as
shown in the formula below:
DC = Duty cycle = V
Example: with V
Current rating decreases with duty cycle because the
LT1576 has internal slope compensation to prevent cur-
rent mode subharmonic switching. For more details, read
Application Note 19. The LT1576 is a little unusual in this
regard because it has nonlinear slope compensation which
gives better compensation with less reduction in current
limit.
Maximum load current would be equal to maximum
switch current for an infinitely large inductor , but with
10
I
I
I
P
P
SW(MAX)
= 1.67 – 0.18 (DC) – 0.32(DC)
= 1.5A for DC 50%
= 1.67 – 0.18 (0.625) – 0.32(0.625)
OUT
U
= 5V, V
OUT
/V
INFORMATION
IN
U
IN
= 8V; DC = 5/8 = 0.625, and;
2
W
for 50% < DC < 90%
P
) of the LT1576.
U
2
= 1.43A
DIV
finite inductor size, maximum load current is reduced by
one-half peak-to-peak inductor current. The following
formula assumes continuous mode operation, implying
that the term on the right is less than one-half of I
For the conditions above and L = 15 H,
At V
1.5A, and I
Note that there is less load current available at the higher
input voltage because inductor ripple current increases.
This is not always the case. Certain combinations of
inductor value and input voltage range may yield lower
available load current at the lowest input voltage due to
reduced peak switch current at high duty cycles. If load
current is close to the maximum available, please check
maximum available current at both input voltage
extremes. To calculate actual peak switch current with a
given set of conditions, use:
For lighter loads where discontinuous operation can be
used, maximum load current is equal to:
I
Continuous Mode
I
I
1 5
OUT(MAX)
SW PEAK
OUT MAX
IN
.
1 5 0 56 0 94
= 15V, duty cycle is 33%, so I
.
2 15 10
OUT(MAX)
.
=
•
I
OUT
1 43
1 43 0 31 1 12
.
.
5 15 5
. A
is equal to:
6
V
I
OUT
P
200 10
2 15 10
2
.
L f V
V
•
V
IN
•
OUT
2
3
.
L f V
V
IN
5 8 5
OUT
P
6
V
15
A
is just equal to a fixed
IN
200 10
IN
V
OUT
•
3
8
P
.