LTC1434CGN Linear Technology, LTC1434CGN Datasheet - Page 9
![IC DC/DC CONV STEP-DOWN 20-SSOP](/photos/7/21/72135/20-ssop_05-08-1641_sml.jpg)
LTC1434CGN
Manufacturer Part Number
LTC1434CGN
Description
IC DC/DC CONV STEP-DOWN 20-SSOP
Manufacturer
Linear Technology
Type
Step-Down (Buck)r
Datasheet
1.LTC1433CGN.pdf
(20 pages)
Specifications of LTC1434CGN
Internal Switch(s)
Yes
Synchronous Rectifier
No
Number Of Outputs
1
Voltage - Output
3.3V, 5V, Adj
Current - Output
450mA
Frequency - Switching
125kHz ~ 240kHz
Voltage - Input
3 ~ 13.5 V
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
20-SSOP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Power - Output
-
APPLICATIONS
Ferrite designs have very low core loss and are preferred
at high switching frequencies, so design goals can con-
centrate on copper loss and preventing saturation. Ferrite
core material saturates “hard,” which means that induc-
tance collapses abruptly when the peak design current is
exceeded. This results in an abrupt increase in inductor
ripple current and consequent output voltage ripple. Do
not allow the core to saturate!
Molypermalloy (from Magnetics, Inc.) is a very good, low
loss core material for toroids, but it is more expensive than
ferrite. A reasonable compromise from the same manu-
facturer is Kool M . Toroids are very space efficient,
especially when you can use several layers of wire. Be-
cause they generally lack a bobbin, mounting is more
difficult. However, designs for surface mount are available
which do not increase the height significantly.
Catch Diode Selection
The catch diode carries load current during the off-time.
The average diode current is therefore dependent on the
P-channel switch duty cycle. At high input voltages the
diode conducts most of the time. As V
the diode conducts only a small fraction of the time. The
most stressful condition for the diode is when the output
is short circuited. Under this condition the diode must
safely handle I
switching diode must also be used to optimize efficiency.
Schottky diodes are a good choice for low forward drop
and fast switching times. Most LTC1433/LTC1434 circuits
will be well served by either a 1N5818, an MBRS130LT3 or
an MBRM5819 Schottky diode.
C
In continuous mode, the source current of the P-channel
MOSFET is a square wave of duty cycle V
prevent large voltage transients, a low ESR input capacitor
sized for the maximum RMS current must be used. The
maximum RMS capacitor current is given by:
This formula has a maximum at V
IN
C required
and C
IN
OUT
Selection
PEAK
I
RMS
U
at close to 100% duty cycle. A fast
I
INFORMATION
MAX
U
V
OUT
W
V
IN
IN
IN
approaches V
V
= 2V
IN
V
OUT
OUT
OUT
U
/V
, where
1 2 /
IN
. To
OUT
I
monly used for design because even significant deviations
do not offer much relief. Note that capacitor manufacturer’s
ripple current ratings are often based on 2000 hours of life.
This makes it advisable to further derate the capacitor, or
choose a capacitor rated at a higher temperature than
required. Several capacitors may also be paralleled to
meet size or height requirements in the design. Always
consult the manufacturer if there is any question.
The selection of C
series resistance (ESR). Typically once the ESR require-
ment is satisfied the capacitance is adequate for filtering.
The output ripple ( V
where f = operating frequency, C
and I
is highest at maximum input voltage since I
with input voltage. For the LTC1433/LTC1434, the general
rule for proper operation is:
Manufacturers such as Nichicon, United Chemicon and
Sanyo should be considered for high performance
through-hole capacitors. The OS-CON semiconductor
dielectric capacitor available from Sanyo has the lowest
ESR/size ratio of any aluminum electrolytic at a some-
what higher price. Once the ESR requirement for C
has been met, the RMS current rating generally far
exceeds the I
In surface mount applications multiple capacitors may
have to be paralleled to meet the ESR or RMS current
handling requirements of the application. Aluminum elec-
trolytic and dry tantalum capacitors are both available in
surface mount configurations. In the case of tantalum, it is
critical that the capacitors are surge tested for use in
switching power supplies. An excellent choice is the AVX
TPS series of surface mount tantalums, available in case
heights ranging from 2mm to 4mm. Other capacitor types
include Sanyo OS-CON, Nichicon PL series and Panasonic
SP series. Consult the manufacturer for other specific
recommendations.
RMS
C
OUT
V
= I
OUT
L
OUT
= ripple current in the inductor. The output ripple
required ESR < 0.25
/2. This simple worst-case condition is com-
RIPPLE(P-P)
I ESR
L
OUT
OUT
is driven by the required effective
LTC1433/LTC1434
4
requirement.
) is determined by:
fC
1
OUT
OUT
= output capacitance
L
increases
9
OUT