LTC1628CG-PG Linear Technology, LTC1628CG-PG Datasheet - Page 21
![IC REG SW 2PHASE STEPDOWN 28SSOP](/photos/6/59/65971/161-28-ssop_sml.jpg)
LTC1628CG-PG
Manufacturer Part Number
LTC1628CG-PG
Description
IC REG SW 2PHASE STEPDOWN 28SSOP
Manufacturer
Linear Technology
Type
Step-Down (Buck)r
Datasheet
1.LTC1628CGPBF.pdf
(32 pages)
Specifications of LTC1628CG-PG
Internal Switch(s)
No
Synchronous Rectifier
Yes
Number Of Outputs
2
Voltage - Output
Adj to 0.8V
Current - Output
3A
Frequency - Switching
220kHz
Voltage - Input
3.5 ~ 30 V
Operating Temperature
0°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
28-SSOP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Power - Output
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LTC1628CG-PG
Manufacturer:
LT
Quantity:
2 000
Part Number:
LTC1628CG-PG
Manufacturer:
LT/凌特
Quantity:
20 000
Part Number:
LTC1628CG-PG#PBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Part Number:
LTC1628CG-PGTRPBF
Manufacturer:
LT/凌特
Quantity:
20 000
APPLICATIO S I FOR ATIO
Fault Conditions: Overvoltage Protection (Crowbar)
The overvoltage crowbar is designed to blow a system
input fuse when the output voltage of the regulator rises
much higher than nominal levels. The crowbar causes
huge currents to flow, that blow the fuse to protect against
a shorted top MOSFET if the short occurs while the
controller is operating.
A comparator monitors the output for overvoltage condi-
tions. The comparator (OV) detects overvoltage faults
greater than 7.5% above the nominal output voltage.
When this condition is sensed, the top MOSFET is turned
off and the bottom MOSFET is turned on until the overvolt-
age condition is cleared. The output of this comparator is
only latched by the overvoltage condition itself and will
therefore allow a switching regulator system having a poor
PC layout to function while the design is being debugged.
The bottom MOSFET remains on continuously for as long
as the OV condition persists; if V
normal operation automatically resumes. A shorted top
MOSFET will result in a high current condition which will
open the system fuse. The switching regulator will regu-
late properly with a leaky top MOSFET by altering the duty
cycle to accommodate the leakage.
The Standby Mode (STBYMD) Pin Function
The Standby Mode (STBYMD) pin provides several choices
for start-up and standby operational modes. If the pin is
pulled to ground, the RUN/SS pins for both controllers are
internally pulled to ground, preventing start-up and thereby
providing a single control pin for turning off both control-
lers at once. If the pin is left open or decoupled with a
capacitor to ground, the RUN/SS pins are each internally
provided with a starting current enabling external control
for turning on each controller independently. If the pin is
provided with a current of >3 A at a voltage greater than
2V, both internal linear regulators (INTV
be on even when both controllers are shut down. In this
mode, the onboard 3.3V and 5V linear regulators can
U
U
OUT
W
returns to a safe level,
CC
and 3.3V) will
U
provide power to keep-alive functions such as a keyboard
controller. This pin can also be used as a latching “on” and/
or latching “off” power switch if so designed.
Frequency of Operation
The LTC1628 has an internal voltage controlled oscillator.
The frequency of this oscillator can be varied over a 2 to 1
range. The pin is internally self-biased at 1.19V, resulting
in a free-running frequency of approximately 220kHz. The
FREQSET pin can be grounded to lower this frequency to
approximately 140kHz or tied to the INTV
approximately 310kHz. The FREQSET pin may be driven
with a voltage from 0 to INTV
oscillator frequency as shown in Figure 5.
Minimum On-Time Considerations
Minimum on-time t
that the LTC1628 is capable of turning on the top MOSFET.
It is determined by internal timing delays and the gate
charge required to turn on the top MOSFET. Low duty cycle
applications may approach this minimum on-time limit
and care should be taken to ensure that
If the duty cycle falls below what can be accommodated by
the minimum on-time, the LTC1628 will begin to skip
cycles. The output voltage will continue to be regulated,
but the ripple voltage and current will increase.
The minimum on-time for the LTC1628 is generally less
than 200ns. However, as the peak sense voltage decreases
the minimum on-time gradually increases up to about
300ns. This is of particular concern in forced continuous
applications with low ripple current at light loads. If the
duty cycle drops below the minimum on-time limit in this
situation, a significant amount of cycle skipping can occur
with correspondingly larger current and voltage ripple.
t
ON MIN
(
)
LTC1628/LTC1628-PG
V f
V
IN
OUT
( )
ON(MIN)
is the smallest time duration
CC
to fix or modulate the
CC
pin to yield
21
1628fb