LTC1702ACGN#TRPBF Linear Technology, LTC1702ACGN#TRPBF Datasheet - Page 10
![IC REG SW DUAL SYNC 2PH 24SSOP](/photos/6/59/65961/161-24-ssop_sml.jpg)
LTC1702ACGN#TRPBF
Manufacturer Part Number
LTC1702ACGN#TRPBF
Description
IC REG SW DUAL SYNC 2PH 24SSOP
Manufacturer
Linear Technology
Series
PolyPhase®r
Type
Step-Down (Buck)r
Datasheet
1.LTC1702ACGNPBF.pdf
(36 pages)
Specifications of LTC1702ACGN#TRPBF
Internal Switch(s)
No
Synchronous Rectifier
No
Number Of Outputs
2
Voltage - Output
0.8 ~ 7 V
Current - Output
1A, 25A
Frequency - Switching
550kHz
Voltage - Input
3 ~ 7 V
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
24-SSOP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Power - Output
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
LTC1702A
APPLICATIONS
amp of continuous current with peak currents up to 5A to
slew large MOSFET gates quickly. The external MOSFETs
are connected with the drain of QT attached to the input
supply and the source of QT at the switching node SW. QB
is the synchronous rectifier with its drain at SW and its
source at PGND. SW is connected to one end of the
inductor, with the other end connected to V
capacitor is connected from V
When a switching cycle begins, QB is turned off and QT is
turned on. SW rises almost immediately to V
inductor current begins to increase. When the PWM pulse
finishes, QT turns off and one nonoverlap interval later, QB
turns on. Now SW drops to PGND and the inductor current
decreases. The cycle repeats with the next tick of the
master clock. The percentage of time spent in each mode
is controlled by the duty cycle of the PWM signal, which in
turn is controlled by the feedback amplifier. The master
clock generates a 1V
turns QT once every 1.8µs. In a typical application with a
5V input and a 1.6V output, the duty cycle will be set at 1.6/
5 × 100% or 32% by the feedback loop. This will give
roughly a 575ns on-time for QT and a 1.22µs on-time for
QB.
This constant frequency operation brings with it a couple
of benefits. Inductor and capacitor values can be chosen
with a precise operating frequency in mind and the feed-
10
U
P-P
, 550kHz sawtooth waveform and
INFORMATION
U
OUT
LTC1702A
to PGND.
W
PV
OUT
CC
Figure 2. Floating TG Driver Supply
PGND
. The output
IN
U
BOOST
and the
SW
TG
BG
D
C
1µF
CP
CP
back loop components can be similarly tightly specified.
Noise generated by the circuit will always be in a known
frequency band with the 550kHz frequency designed to
leave the 455kHz IF band free of interference. Subharmonic
oscillation and slope compensation, common headaches
with constant frequency current mode switchers, are
absent in voltage mode designs like the LTC1702A.
During the time that QT is on, its source (the SW pin) is at
V
ever, QT requires V
minimum R
LTC1702A— it needs to generate a gate drive signal at TG
higher than its highest supply voltage. To get around this,
the TG driver runs from floating supplies, with its negative
supply attached to SW and its power supply at BOOST.
This allows it to slew up and down with the source of QT.
In combination with a simple external charge pump (Fig-
ure 2), this allows the LTC1702A to completely enhance
the gate of QT without requiring an additional, higher
supply voltage.
The two channels of the LTC1702A run from a common
clock, with the phasing chosen to be 180° from side 1 to
side 2. This has the effect of doubling the frequency of the
switching pulses seen by the input bypass capacitor, sig-
nificantly lowering the RMS current seen by the capacitor
and reducing the value required (see the 2-Phase section).
IN
. V
V
IN
QT
QB
IN
is also the power supply for the LTC1702A. How-
L
EXT
ON
+
+
. This presents a problem for the
C
C
OUT
IN
1702A F02
IN
V
OUT
+ V
GS(ON)
at its gate to achieve
1702afa