LTC3857IUH#PBF Linear Technology, LTC3857IUH#PBF Datasheet - Page 17

• Manufacturer Part Number: LTC3857IUH#PBF
• Description: IC CTRLR STP-DN SYNC DUAL 32QFN
• Manufacturer: Linear Technology
• Series: PolyPhase®r
• Type: Step-Down (Buck)r

Specifications of LTC3857IUH#PBF

• Internal Switch(s): No
• Synchronous Rectifier: Yes
• Number Of Outputs: 2
• Voltage - Output: 0.8 ~ 24 V
• Frequency - Switching: 50kHz ~ 900kHz
• Voltage - Input: 4 ~ 38 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 32-QFN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Current - Output: -
• Power - Output: -

The equivalent resistance R1|| R2 is scaled to the room
temperature inductance and maximum DCR:
The sense resistor values are:
The maximum power loss in R1 is related to duty cycle,
and will occur in continuous mode at the maximum input
voltage:
Ensure that R1 has a power rating higher than this value.
If high efficiency is necessary at light loads, consider this
power loss when deciding whether to use DCR sensing or
sense resistors. Light load power loss can be modestly
higher with a DCR network than with a sense resistor, due
to the extra switching losses incurred through R1. However,
DCR sensing eliminates a sense resistor, reduces conduc-
tion losses and provides higher efficiency at heavy loads.
Peak efficiency is about the same with either method.
Inductor Value Calculation
The operating frequency and inductor selection are inter-
related in that higher operating frequencies allow the use
of smaller inductor and capacitor values. So why would
anyone ever choose to operate at lower frequencies with
larger components? The answer is efficiency. A higher
frequency generally results in lower efficiency because
of MOSFET gate charge losses. In addition to this basic
trade-off, the effect of inductor value on ripple current and
low current operation must also be considered.
The inductor value has a direct effect on ripple current. The
inductor ripple current, ∆I
tance or higher frequency and increases with higher V
APPLICATIONS INFORMATION
R1||R2=
R1=
P
ΔI
LOSS
L
=
R1||R2
( )
f
R
R1=
1
D
( )
(
L
DCR at 20°C
(
V
; R2=
V
OUT
IN(MAX)
⎛
⎝ ⎜
L
1–
R1•R
1–R
–V
V
R1
L
V
OUT
, decreases with higher induc-
)
D
OUT
IN
D
•C1
⎞
⎠ ⎟
)
•V
OUT
IN
:
Accepting larger values of ∆I
inductances, but results in higher output voltage ripple
and greater core losses. A reasonable starting point for
setting ripple current is ∆I
∆I
The inductor value also has secondary effects. The tran-
sition to Burst Mode operation begins when the average
inductor current required results in a peak current below
15% of the current limit determined by R
inductor values (higher ∆I
lower load currents, which can cause a dip in efficiency in
the upper range of low current operation. In Burst Mode
operation, lower inductance values will cause the burst
frequency to decrease.
Inductor Core Selection
Once the value for L is known, the type of inductor must
be selected. High efficiency converters generally cannot
afford the core loss found in low cost powdered iron cores,
forcing the use of more expensive ferrite or molypermalloy
cores. Actual core loss is independent of core size for a
fixed inductor value, but it is very dependent on inductance
value selected. As inductance increases, core losses go
down. Unfortunately, increased inductance requires more
turns of wire and therefore copper losses will increase.
Ferrite designs have very low core loss and are preferred
for high switching frequencies, so design goals can
concentrate on copper loss and preventing saturation.
Ferrite core material saturates hard, which means that
inductance collapses abruptly when the peak design current
is exceeded. This results in an abrupt increase in inductor
ripple current and consequent output voltage ripple. Do
not allow the core to saturate!
Power MOSFET and Schottky Diode (Optional)
Selection
Two external power MOSFETs must be selected for each
controller in the LTC3857: one N-channel MOSFET for the
top (main) switch, and one N-channel MOSFET for the
bottom (synchronous) switch.
L
occurs at the maximum input voltage.
L
L
) will cause this to occur at
= 0.3(I
L
allows the use of low
MAX
LTC3857
). The maximum
SENSE
. Lower
17
3857fc