MIC4684-5.0BM Micrel Inc, MIC4684-5.0BM Datasheet - Page 2
![IC REG BUCK HI EFF 2A 5.0V 8SOIC](/photos/6/50/65078/576-8-soic_sml.jpg)
MIC4684-5.0BM
Manufacturer Part Number
MIC4684-5.0BM
Description
IC REG BUCK HI EFF 2A 5.0V 8SOIC
Manufacturer
Micrel Inc
Series
SuperSwitcher™r
Type
Step-Down (Buck)r
Datasheet
1.MIC4684-3.3BM_TR.pdf
(16 pages)
Specifications of MIC4684-5.0BM
Internal Switch(s)
Yes
Synchronous Rectifier
No
Number Of Outputs
1
Voltage - Output
5V
Current - Output
2A
Frequency - Switching
200kHz
Voltage - Input
4 ~ 30 V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
8-SOIC (3.9mm Width)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Power - Output
-
Micrel, Inc.
Pin Configuration
Pin Description
Detailed Pin Description
Switch (SW, pin 1)
The switch pin is tied to the emitter of the main internal NPN
transistor. This pin is biased up to the input voltage minus the
V
negative when the output inductor’s magnetic field collapses
at turn-off. During the OFF time the SW pin is clamped by
the output schottky diode to a –0.5V typically.
Ground (GND, pins 2,6,7)
There are two main areas of concern when it comes to the
ground pin, EMI and ground current. In a buck regulator
or any other non-isolated switching regulator the output
capacitor(s) and diode(s) ground is referenced back to the
switching regulator’s or controller’s ground pin. Any resistance
between these reference points causes an offset voltage/IR
drop proportional to load current and poor load regulation.
This is why its important to keep the output grounds placed
as close as possible to the switching regulator’s ground pin.
To keep radiated EMI to a minimum its necessary to place
the input capacitor ground lead as close as possible to the
switching regulators ground pin.
Input Voltage (V
The V
This pin is also connected to the internal regulator. The output
diode or clamping diode should have its cathode as close as
possible to this point to avoid voltage spikes adding to the
voltage across the collector.
January 2010
SAT
of the main NPN pass element. The emitter is also driven
Pin Number
IN
2, 6, 7
pin is the collector of the main NPN pass element.
1
3
4
5
8
IN
, pin 3)
Pin Name
GND
SW
EN
BS
FB
IN
GND
VIN
SW
BS
1
2
3
4
Pin Function
Switch (Output): Emitter of NPN output switch. Connect to external storage
inductor and Shottky diode.
Ground
Supply (Input): Unregulated +4V to 30V supply voltage (34V transient)
Booststrap Voltage Node (External Component): Connect to external boost
capacitor.
Feedback (Input): Outback voltage feedback to regulator. Connect to output
of supply for fixed versions. Connect to 1.23V tap of resistive divider for
adjustable versions.
Enable (Input): Logic high = enable; logic low = shutdown
8-Pin SOP (M)
2
Bootstrap (BS, pin 4)
The bootstrap pin in conjunction with the external bootstrap
capacitor provides a bias voltage higher than the input volt-
age to the MIC4684’s main NPN pass element. The bootstrap
capacitor sees the dv/dt of the switching action at the SW
pin as an AC voltage. The bootstrap capacitor then couples
the AC voltage back to the BS pin plus the dc offset of V
where it is rectified and used to provide additional drive to
the main switch, in this case a NPN transistor.
This additional drive reduces the NPN’s saturation voltage and
increases efficiency, from a V
to a V
Feedback (FB, pin 5)
The feedback pin is tied to the inverting side of a GM error
amplifier. The noninverting side is tied to a 1.235V bandgap
reference. Fixed voltage versions have an internal voltage
divider from the feedback pin. Adjustable versions require an
external resistor voltage divider from the output to ground,
with the center tied to the feedback pin.
Enable (EN, pin 8)
The enable (EN) input is used to turn on the regulator and is
TTL compatible. Note: connect the enable pin to the input if
unused. A logic-high enables the regulator. A logic-low shuts
down the regulator and reduces the stand-by quiescent
input current to typically 150µA. The enable pin has an up-
per threshold of 2.0V minimum and lower threshold of 0.8V
maximum. The hysterisis provided by the upper and lower
thresholds acts as an UVLO and prevents unwanted turn on
of the regulator due to noise.
SAT
8 EN
7
6
5
of 0.5V and 88% efficiency respectively.
GND
GND
FB
SAT
of 1.8V, and 75% efficiency
M9999-012610
MIC4684
IN