MIC2182-5.0YM TR Micrel Inc, MIC2182-5.0YM TR Datasheet - Page 16
![IC CTRLR SYNC BUCK 5.0V 16-SOIC](/photos/7/42/74248/16-sop_pkg_sml.jpg)
MIC2182-5.0YM TR
Manufacturer Part Number
MIC2182-5.0YM TR
Description
IC CTRLR SYNC BUCK 5.0V 16-SOIC
Manufacturer
Micrel Inc
Type
Step-Down (Buck)r
Datasheet
1.MIC2182-5.0YSM.pdf
(28 pages)
Specifications of MIC2182-5.0YM TR
Internal Switch(s)
No
Synchronous Rectifier
Yes
Number Of Outputs
1
Voltage - Output
5V
Current - Output
20A
Frequency - Switching
300kHz
Voltage - Input
4.5 ~ 16.5 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
16-SOIC (3.9mm Width)
Power - Output
400mW
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
MIC2182-5.0YMTR
MIC2182-5.0YMTR
MIC2182-5.0YMTR
MIC2182
Applications Information
The following applications information includes component
selection and design guidelines. See Figure 14 and Tables 1
through 5 for predesigned circuits.
Inductor Selection
Values for inductance, peak, and RMS currents are required
to select the output inductor. The input and output voltages
and the inductance value determine the peak to peak inductor
ripple current. Generally, higher inductance values are used
with higher input voltages. Larger peak to peak ripple currents
will increase the power dissipation in the inductor and
MOSFETs. Larger output ripple currents will also require
more output capacitance to smooth out the larger ripple
current. Smaller peak to peak ripple currents require a larger
inductance value and therefore a larger and more expensive
inductor. A good compromise between size, loss and cost is
to set the inductor ripple current to be equal to 20% of the
maximum output current.
The inductance value is calculated by the equation below.
where:
The peak-to-peak inductor current (ac ripple current) is:
The peak inductor current is equal to the average output
current plus one half of the peak to peak inductor ripple
current.
The RMS inductor current is used to calculate the I
in the inductor.
Maximizing efficiency requires the proper selection of core
material and minimizing the winding resistance. The high
frequency operation of the MIC2182 requires the use of ferrite
materials for all but the most cost sensitive applications.
Lower cost iron powder cores may be used but the increase
in core loss will reduce the efficiency of the power supply. This
is especially noticeable at low output power. The winding
resistance decreases efficiency at the higher output current
levels. The winding resistance must be minimized although
this usually comes at the expense of a larger inductor.
The power dissipated in the inductor is equal to the sum of the
core and copper losses. At higher output loads, the core
losses are usually insignificant and can be ignored. At lower
M9999-042204
f
0.2 = ratio of ac ripple current to dc output current
V
L
I
I
I
S
PP
PK
inductor
IN(max)
= switching frequency
V
IN(max)
I
V
V
OUT(max)
OUT
(rms) I
OUT
= maximum input voltage
V
IN(max)
(V
(V
f
S
OUT(max)
IN(max)
IN(max)
0.5 I
0.2 I
f
S
PP
OUT(max)
V
V
L
OUT
OUT
1
)
)
3
1
I
OUT(max)
I
PP
2
2
·R losses
16
output currents, the core losses can be a significant contribu-
tor. Core loss information is usually available from the mag-
netics vendor.
Copper loss in the inductor is calculated by the equation
below:
The resistance of the copper wire, R
temperature. The value of the winding resistance used should
be at the operating temperature.
where:
Current-Sense Resistor Selection
Low inductance power resistors, such as metal film resistors
should be used. Most resistor manufacturers make low
inductance resistors with low temperature coefficients, de-
signed specifically for current-sense applications. Both resis-
tance and power dissipation must be calculated before the
resistor is selected. The value of R
the maximum output current and the maximum threshold
level. The power dissipated is based on the maximum peak
output current at the minimum overcurrent threshold limit.
The maximum overcurrent threshold is:
The maximum power dissipated in the sense resistor is:
MOSFET Selection
External N-channel logic-level power MOSFETs must be
used for the high- and low-side switches. The MOSFET gate-
to-source drive voltage of the MIC2182 is regulated by an
internal 5V V
operation is specified at V
It is important to note the on-resistance of a MOSFET
increases with increasing temperature. A 75 C rise in junc-
tion temperature will increase the channel resistance of the
MOSFET by 50% to 75% of the resistance specified at 25 C.
This change in resistance must be accounted for when
calculating MOSFET power dissipation.
Total gate charge is the charge required to turn the MOSFET
on and off under specified operating conditions (V
V
circuit. At 300kHz switching frequency and above, the gate
R
GS
winding(hot)
). The gate charge is supplied by the MIC2182 gate drive
T
T
R
P
R
I
P
overcurrent(max)
HOT
20 C
D(R
inductor Cu
winding(20 C)
SENSE
under operating load
(usually specified by the manufacturer)
SENSE
= temperature of the wire
= ambient temperature
DD
R
)
winding(20 C)
I
OUT(max)
regulator. Logic-level MOSFETs, whose
75mV
I
I
overcurrent(max)
inductor
is room temperature winding resistance
135mV
R
(rms)
GS
CS
= 4.5V must be used.
1 0.0042 (T
2
2
SENSE
R
winding
R
winding
CS
is chosen based on
, increases with
hot
April 22, 2004
T
20 C
DS
Micrel
)
and