LM3478MMX/NOPB National Semiconductor, LM3478MMX/NOPB Datasheet - Page 11
![IC CTRLR SW REG N-CH 8MSOP](/photos/6/57/65756/pkg_mua08a_sml.jpg)
LM3478MMX/NOPB
Manufacturer Part Number
LM3478MMX/NOPB
Description
IC CTRLR SW REG N-CH 8MSOP
Manufacturer
National Semiconductor
Type
Step-Up (Boost), Flyback, Sepicr
Datasheet
1.LM3478MMNOPB.pdf
(24 pages)
Specifications of LM3478MMX/NOPB
Internal Switch(s)
No
Synchronous Rectifier
No
Number Of Outputs
1
Voltage - Output
Adjustable
Current - Output
1A
Frequency - Switching
100kHz ~ 1MHz
Voltage - Input
2.97 ~ 40 V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
8-MSOP, Micro8™, 8-uMAX, 8-uSOP,
Dc To Dc Converter Type
Step Up
Pin Count
8
Input Voltage
2.97 to 40V
Output Voltage
1.26V
Output Current
1A
Package Type
MSOP
Mounting
Surface Mount
Operating Temperature Classification
Automotive
Operating Temperature (min)
-40C
Operating Temperature (max)
125C
For Use With
LM3478EVAL - BOARD EVALUATION LM3478
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Power - Output
-
Lead Free Status / Rohs Status
Compliant
Other names
*LM3478MMX
*LM3478MMX/NOPB
LM3478MMX
*LM3478MMX/NOPB
LM3478MMX
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LM3478MMX/NOPB
Manufacturer:
ALLEN BRADLEY
Quantity:
1 000
Part Number:
LM3478MMX/NOPB
Manufacturer:
TI
Quantity:
20 000
the scenario is identical to a step change in the load current,
so the response at the output voltage is the same as would
be observed in a step load change. Hence, the output voltage
overshoot here can also trigger OVP. The LM3478 will regu-
late in hysteretic mode for several cycles, or may not recover
and simply stay in hysteretic mode until the load current drops
or Vin is not crossing the 7.2V threshold anymore. Note that
the output is still regulated in hysteretic mode.
Depending on the requirements of the application there is
some influence one has over this effect. The threshold of 7.2V
can be shifted to higher voltages by adding a resistor in series
with Vin. In case Vin is right at the threshold of 7.2V it can
happen that the threshold is crossed over and over due to
some slight ripple on Vin. To minimize the effect on the output
voltage one can filter the Vin pin with an RC filter.
10135511
FIGURE 1. The Feedback Voltage Experiences an
Oscillation if the Input Voltage crosses the 7.2V Internal
Bias Threshold
10135507
FIGURE 2. Basic Operation of the PWM Comparator
SLOPE COMPENSATION RAMP
The LM3478 uses a current mode control scheme. The main
advantages of current mode control are inherent cycle-by-cy-
cle current limit for the switch and simpler control loop char-
acteristics. It is also easy to parallel power stages using
current mode control since current sharing is automatic. How-
ever, current mode control has an inherent instability for duty
cycles greater than 50%, as shown in Figure 3.
A small increase in the load current causes the switch current
to increase by ΔI
. The effect of this load change is ΔI
.
10135512
0
1
The two solid waveforms shown are the waveforms compared
FIGURE 3. Sub-Harmonic Oscillation for D>0.5 and
at the internal pulse width modulator, used to generate the
Compensation Ramp to Avoid Sub-Harmonic Oscillation
MOSFET drive signal. The top waveform with the slope S
is
e
the internally generated control waveform V
. The bottom
C
waveform with slopes S
and S
is the sensed inductor current
n
f
waveform V
.
SEN
11
www.national.com