LM2593HVT-5.0/NOPB National Semiconductor, LM2593HVT-5.0/NOPB Datasheet
LM2593HVT-5.0/NOPB
Specifications of LM2593HVT-5.0/NOPB
*LM2593HVT-5.0/NOPB
LM2593HVT-5.0
Related parts for LM2593HVT-5.0/NOPB
LM2593HVT-5.0/NOPB Summary of contents
Page 1
... Typical Application (Fixed Output Voltage Versions) SIMPLE SWITCHER ® and Switchers Made Simple ® are registered trademarks of National Semiconductor Corporation. © 2001 National Semiconductor Corporation Power Converter 150 kHz 2A ® Features n 3.3V, 5V, and adjustable output versions n Adjustable version output voltage range, 1.2V to 57V ± ...
Page 2
... Absolute Maximum Ratings If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Maximum Supply Voltage ( /SS Pin Input Voltage (Note 2) Delay Pin Voltage (Note 2) Flag Pin Voltage Feedback Pin Voltage Output Voltage to Ground (Steady State) ...
Page 3
LM2593HV-ADJ Electrical Characteristics Specifications with standard type face are for T ture Range. Symbol Parameter Efficiency V = 12V All Output Voltage Versions Electrical Characteristics Specifications with standard type face are for T ture Range. Unless otherwise specified, ...
Page 4
All Output Voltage Versions Electrical Characteristics Specifications with standard type face are for T ture Range. Unless otherwise specified, V Symbol Parameter FLAG/DELAY CONTROL Test Circuit of Figure 1 Regulator Dropout Detector Threshold Voltage VF Flag Output Saturation SAT Voltage ...
Page 5
Typical Performance Characteristics Normalized Output Voltage 10133302 Switch Saturation Voltage 10133305 Operating Quiescent Current 10133308 (Circuit of Figure 1 ) Line Regulation 10133303 Switch Current Limit 10133306 Shutdown Quiescent Current 10133309 5 Efficiency 10133304 Dropout Voltage 10133307 Minimum Operating Supply ...
Page 6
Typical Performance Characteristics Feedback Pin Bias Current 10133311 Soft-start 10133314 Soft-start Response 10133318 www.national.com (Circuit of Figure 1 ) (Continued) Flag Saturation Voltage 10133312 Shutdown /Soft-start Current 10133315 Shutdown/Soft-start Threshold Voltage Internal Gain-Phase Characteristics 10133353 6 Switching Frequency 10133313 Delay ...
Page 7
... Horizontal Time Base: 50 µs/div. A: Output Voltage, 100 mV/div. (AC) B: 500 Load Pulse Connection Diagrams and Order Information Bent and Staggered Leads, Through Hole Package 7-Lead TO-220 (T) Order Number LM2593HVT-3.3, LM2593HVT-5.0, or LM2593HVT-ADJ See NS Package Number TA07B (Circuit of Figure 1 ) (Continued) Discontinuous Mode Switching Waveforms = 2A ...
Page 8
Test Circuit and Layout Guidelines Component Values shown are for V = 15V 5V 2A. OUT LOAD C — 470 µF, 50V, Aluminum Electrolytic Nichicon “PM Series” — 220 µF, 25V Aluminum Electrolytic, ...
Page 9
Block Diagram PIN FUNCTIONS +V (Pin 1) — This is the positive input supply for the IC IN switching regulator. A suitable input bypass capacitor must be present at this pin to minimize voltage transients and to supply the switching ...
Page 10
PIN FUNCTIONS (Continued) Note If any of the above three features (Shutdown /Soft-start, Error Flag, or Delay) are not used, the respective pins can be left open. www.national.com FIGURE 2. Soft-Start, Delay, Error Output 10 10133331 ...
Page 11
INDUCTOR VALUE SELECTION GUIDES (For Continuous Mode Operation) FIGURE 3. Timing Diagram for 5V Output FIGURE 4. LM2593HV-3.3 11 10133332 10133365 www.national.com ...
Page 12
INDUCTOR VALUE SELECTION GUIDES www.national.com (For Continuous Mode Operation) (Continued) FIGURE 5. LM2593HV-5.0 FIGURE 6. LM2593HV-ADJ 12 10133366 10133367 ...
Page 13
INDUCTOR VALUE SELECTION GUIDES Coilcraft Inc. Coilcraft Inc., Europe Pulse Engineering Inc. Pulse Engineering Inc., Europe Renco Electronics Inc. Schott Corp. Cooper Electronic Tech. (Coiltronics) FIGURE 8. Contact Information for Suggested Inductor Manufacturers (For Continuous Mode Operation) (Continued) FIGURE 7. ...
Page 14
Application Information INDUCTOR SELECTION PROCEDURE Application Note AN-1197 titled ’Selecting Inductors for Buck Converters’ provides detailed information on this topic. For a quick-start the designer may refer to the nomographs pro- vided in Figure 4 to Figure ...
Page 15
Application Information Therefore, looking at Figure 4 we quick-select a 47µH/2A inductor (designed for 150 kHz operation) for this applica- tion should confirm that it is rated to handle 200 µJ (see Figure the procedure ...
Page 16
Application Information FIGURE 9. Typical Circuit Using Shutdown /Soft-start and Error Flag Features FIGURE 10. Inverting −5V Regulator With Shutdown and Soft-start lNVERTING REGULATOR The circuit in Figure 10 converts a positive input voltage to a negative output voltage with ...
Page 17
Application Information suming 100% efficiency, which is never so. Therefore expect additional 10-20% higher than calculated from PEAK the above equation. The reader is also referred to Application Note AN-1157 for examples based on positive to ...
Page 18
Application Information on the regulated positive output for the charge pump to work correctly. Also, resistor R1 is required to limit the charging current some value less than the LM2593HV current limit. FIGURE 14. Charge Pump for ...
Page 19
Application Information FIGURE 15. Junction Temperature Rise, TO-263 Layout Suggestions As in any switching regulator, layout is very important. Rap- idly switching currents associated with wiring inductance can generate voltage transients which can cause problems. For minimal inductance and ground ...
Page 20
... Physical Dimensions unless otherwise noted Order Number LM2593HVT-3.3, LM2593HVT-5.0 or LM2593HVT-ADJ www.national.com inches (millimeters) 7-Lead TO-220 Bent and Staggered Package NS Package Number TA07B 20 ...
Page 21
... NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant ...