LM2575T-ADJG ON Semiconductor, LM2575T-ADJG Datasheet - Page 8
![IC REG SW 1A ADJ STEPDWN TO220-5](/photos/7/61/76166/to-220-5_314d-04_sml.jpg)
LM2575T-ADJG
Manufacturer Part Number
LM2575T-ADJG
Description
IC REG SW 1A ADJ STEPDWN TO220-5
Manufacturer
ON Semiconductor
Type
Step-Down (Buck)r
Datasheet
1.LM2575T-5G.pdf
(28 pages)
Specifications of LM2575T-ADJG
Internal Switch(s)
Yes
Synchronous Rectifier
No
Number Of Outputs
1
Voltage - Output
1.23 ~ 37 V
Current - Output
1A
Frequency - Switching
52kHz
Voltage - Input
4.75 ~ 40 V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Through Hole
Package / Case
TO-220-5 (Straight Leads)
Output Voltage
1.23 V to 37 V
Output Current
1 A
Input Voltage
4.75 V to 40 V
Switching Frequency
52 KHz
Operating Temperature Range
- 40 C to + 125 C
Mounting Style
Through Hole
Duty Cycle (max)
98 %
Primary Input Voltage
40V
No. Of Outputs
1
No. Of Pins
5
Filter Terminals
Through Hole
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Power - Output
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
LM2575T-ADJGOS
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LM2575T-ADJG
Manufacturer:
ON Semiconductor
Quantity:
2
Part Number:
LM2575T-ADJG
Manufacturer:
ON/安森美
Quantity:
20 000
Buck Converter Basics
is the most elementary forward−mode converter. Its basic
schematic can be seen in Figure 15.
time periods. The first one occurs when the series switch is
on, the input voltage is connected to the input of the inductor.
rectifier (or catch diode) is reverse biased. During this
period, since there is a constant voltage source connected
across the inductor, the inductor current begins to linearly
ramp upwards, as described by the following equation:
material in the form of magnetic flux. If the inductor is
properly designed, there is sufficient energy stored to carry
the requirements of the load during the “off” period.
When the power switch turns off, the voltage across the
inductor reverses its polarity and is clamped at one diode
voltage drop below ground by catch dioded. Current now
flows through the catch diode thus maintaining the load
PIN FUNCTION DESCRIPTION
Pin
The LM2575 is a “Buck” or Step−Down Converter which
The operation of this regulator topology has two distinct
The output of the inductor is the output voltage, and the
During this “on” period, energy is stored within the core
The next period is the “off” period of the power switch.
1
2
3
4
5
V
in
Feedback
ON/OFF
Symbol
Switch
Figure 15. Basic Buck Converter
Output
Power
GND
V
in
I
L(on)
+
This pin is the positive input supply for the LM2575 step−down switching regulator. In order to minimize
voltage transients and to supply the switching currents needed by the regulator, a suitable input bypass
capacitor must be present (C
This is the emitter of the internal switch. The saturation voltage V
It should be kept in mind that the PCB area connected to this pin should be kept to a minimum in order to
minimize coupling to sensitive circuitry.
Circuit ground pin. See the information about the printed circuit board layout.
This pin senses regulated output voltage to complete the feedback loop. The signal is divided by the
internal resistor divider network R2, R1 and applied to the non−inverting input of the internal error amplifier.
In the Adjustable version of the LM2575 switching regulator this pin is the direct input of the error amplifier
and the resistor network R2, R1 is connected externally to allow programming of the output voltage.
It allows the switching regulator circuit to be shut down using logic level signals, thus dropping the total
input supply current to approximately 80 mA. The input threshold voltage is typically 1.4 V. Applying a
voltage above this value (up to +V
1.4 V or if this pin is connected to ground, the regulator will be in the “on” condition.
D1
V
in
V out t on
L
L
C
out
DESIGN PROCEDURE
in
V
out
http://onsemi.com
in Figure 1).
R
Load
in
) shuts the regulator off. If the voltage applied to this pin is lower than
Description (Refer to Figure 1)
8
current loop. This removes the stored energy from the
inductor.
The inductor current during this time is:
turned on. Regulation of the converter is accomplished by
varying the duty cycle of the power switch. It is possible to
describe the duty cycle as follows:
cycle can also be described as:
of the catch diode voltage and the inductor current.
This period ends when the power switch is once again
For the buck converter with ideal components, the duty
Figure 16 shows the buck converter idealized waveforms
d +
t on
T
, where T is the period of switching.
I
sat
L(off)
of this output switch is typically 1.0 V.
+
d +
V
out
V out
V
in
L
V
D
t
off